95
WARRANtY CLAUsEs
The engines manufactured by Lombardini Marine are covered by a 24-months
warranty beginning on the date of delivery to the first user in accordance
with european directive 1999/44/eeC and for at most 36 months from date
of delivery to the manufacturer or shipyard; of the two alternatives, that
which occurs first shall apply.
in the case of special applications requiring major alterations to the cooling,
lubrication, supercharging and-filtering circuits, the special warranty clauses
agreed in writing shall apply or the general clauses indicated above in the
event of an application approval test certificate being produced, issued by
the Technical department of Lombardini Marine.
Within the above time-frame, Lombardini Marine undertakes to make any
repairs under warranty, either directly or through authorized workshops.
The obligations of Lombardini Marine, as indicated in european directive
1999/44/eeC, shall not be valid in the following cases:
- engines not installed and used in conformity with the instructions of Lom-
bardini Marine shown in the operator’s and maintenance booklet;
- Seals affixed by Lombardini Marine tampered with;
- engines repaired, dismantled or modified by workshops not authorized by
Lombardini Marine;
- Fitting of not-original Lombardini Marine spare parts;
- injection Systems damaged by unsuitable or polluted fuel.
Upon expiry of the 24-months period from the date of delivery of the engine
to the first user, without Lombardini Marine or its authorized workshops
having received notification of any faults, Lombardini Marine shall consider
itself exempted from all liability or obligations, as set forth in european
directive 1999/44/eeC.
This warranty, effective from 23/3/2002, cancels and replaces all other
previous warranties and any amendments made to it shall be made in writing.
Содержание LDW 194 JMtI
