manualshive.com logo in svg

Lomax STANCE, Руководство по установке

Поделиться
Скачать
Lomax STANCE Скачать руководство пользователя страница 2

2

PREPARATION

Ensure air and surface temperatures are above 60° F. Unpack cover components and 

clean truck box if dirty. For additional installation assistance, go to lomaxcovers.com 

for install video.

COMPONENTS

• (8) Clamps

• (2) Anchors

• (2) Driver side rails

• (2) Passenger side rails

• Pre-folded cover assembly

TOOLS NEEDED

• 1/2” Wrench

• Ft-lbs torque wrench with 1/2” socket

• Marking tool

• Protective eyewear

• 7/16” Wrench

• Spring clamp (optional)

NOTE: 

With an under the rail drop-in bed liner, installation is possible with minimal 

trimming/cutting of bed liner at front corner of box and back by tailgate to allow side 

rail to install properly. Considerable trimming/cutting is required with an over the rail 

drop-in bed liner.

NOTE: 

For additional protection against the elements, locate and seal miscellaneous 

factory holes, crevices, stake pockets, etc. that may be in box (sealant not included).

NOTE: 

Tonneau cover and side rail appearance may vary. Typically a vehicle with a 6’ 

or longer box is provided with two multi-piece side rails.

!

CAUTION: Over torquing hardware may damage components.

PARTS DIAGRAM

Clamps

Driver side rails

Safety strap 

hole toward 

front of box

Rear

Latches on 

rear panel

Cover assembly

Passenger 

side rails

Front

 (closest to cab) 

Storage brackets on 

header panel

Pivot link in clip

(underneath)

Anchors

Pre-installed 

assembly 

bracket

Содержание STANCE

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды