Logan 650-1 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 12

background image

For best results use only

authentic Logan blades

INSTRUCTION MANUAL

MODEL 650-1 / 655-1 / 660-1

FRAMER’S EDGE ELITE

MAT CUTTER

INSTRUCTIONS AND OPERATION MANUAL

Professional Series mat cutting system with laminate board surface,

ball bearing guided cutting head, production stops, 9” & 32”

squaring arms, plus dual straight & bevel cutting heads

Uses Logan Replacement

Blade #269 Blade #268

L618DN4 Rev.3 1-16

Purchase Date

ID Number (on bottom of board)

Date (on bottom of board)

LoganGraphic.com

Model 650-1 Framer’s Edge Elite - 40” mat cutter
Model 655-1 Framer’s Edge Elite - 48” mat cutter
Model 660-1 Framer’s Edge Elite - 60” mat cutter

CAUTION!!

MAT CUTTING BLADES ARE SHARP

1
2
3
...
»

Содержание 650-1













Отзывы:

Нет отзывов

Похожие инструкции для 650-1

Бренд: Gardenia Страницы: 40

Бренд: Olympia Страницы: 10

Бренд: Power Fist Страницы: 16

Бренд: D-CUT Страницы: 7

Бренд: D-CUT Страницы: 6

Бренд: Mafell Страницы: 114

Бренд: Vari Страницы: 18

Бренд: Rockwell Страницы: 20

Бренд: Makita Страницы: 12

Бренд: Makita Страницы: 40

SuperCut Construction FSC 2.0

Бренд: Fein Страницы: 16

Бренд: Locoloc Страницы: 16

Бренд: SIZZIX Страницы: 12

Бренд: QEP Страницы: 2

Бренд: Hengstler Страницы: 4

Бренд: Maruyama Страницы: 32

Бренд: Maruyama Страницы: 56

Бренд: Maruyama Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды