LOFTNESS 60MH Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 50

background image

15

Hydraulic Flail Mower OM

Maintenance

Adjusting Height of Cut

This procedure should be performed on a level surface
with mower mounted on tractor.

The flail mower uses slotted adjustments on the rear
roller to allow an infinite cutting height adjustment from
0 to 4-1/2".

To adjust the height of cut:

1. Set bucket tilt cylinders to carry flail mower level

from front to rear.

2. Turn off all power to the flail mower.

DANGER:

Failure to turn off power to the flail

mower before adjusting the cutting height
could result in serious injury or death.

3. Manually position knife rotor until the bottom row of

knives is at the lowest operating position.

2

3

1

4. Set blocks (1) under skid shoes at the desired

cutting height.

5. Loosen the nuts of the 5/8" carriage bolt (2) and

the 5/8" pivot bolt (3) on both sides of the mower.
Repeat on opposite side of the flail mower.

6. Allow steel roller to contact ground.

7. Retighten the 5/8" nuts to 170 ft. lbs.

8. Remove blocks from under skid shoes.

5

4

9. Adjust the skid shoes 1"-2" from ground to prevent

scalping by means of the 1/2" carriage bolts (4) and
the 1/2" pivot bolts (5). Repeat on opposite side of
the flail mower.

«
...
19
20
21
22
23
...
»

Содержание 60MH



















































Отзывы:

Нет отзывов

Похожие инструкции для 60MH

Бренд: MTD Страницы: 16

Бренд: Echo Страницы: 244

Бренд: Flymo Страницы: 11

Бренд: Barbieri Страницы: 2

Бренд: Honda Страницы: 21

Бренд: Zoef Robot Страницы: 54

Flymo Micro Compact 300 Plus

Бренд: Electrolux Страницы: 12

Бренд: Kubota Страницы: 124

sunjoe 24V-CRLM15

Бренд: SNOWJOE Страницы: 64

Бренд: Sabo Страницы: 99

Бренд: Sabo Страницы: 114

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды