Loewe Xelos 32 SL Скачать руководство пользователя страница 13

Страница: 13 / 76

13 -

For TV sets with MHEG-5 software the stations are tied
to “Logical Channel Numbers” – “LCN” and sorted from
1-799. Digital stations without “LCN” are stored from
800 onwards. Analogue stations are stored from 1001.

You can state whether coded stations are to be searched
for in the search/update.

Select

yes

to save all found

scrambled stations. However, these stations can only
be received in connection with a CA module and the
appropriate Smart Card.

Handling of the CA module is

described on page 40.
If a CA module with a SmartCard is already plugged in for
the station search, all the stations which this module can
descramble are also saved when

is preset.

If you are using an active antenna, then select

yes (5V)

for the antenna power supply.

The conventional settings will be derived from the selec-
tion of set location. Only change this if you know other
symbol rates and modulation types or if you have to
specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
lite, the rate of 6900 might have to be replaced by 6111.
Information is available from your cable network provider.
If you want to run the station search independently of
the channel grid, select

frequency search

for the search

method.

State how (single satellite or type of satellite system) you
receive which satellite(s). Ask your dealer if in doubt.

Specify here whether the high band of the selected satel-
lite is to be searched in addition to the low band.

Normally, you do not need to change the values for high
and low band, unless the LNC (LNB) of your satellite
system uses a different oscillator frequency (important
for the frequency display).
After you have made these settings, you should receive
the picture and sound of the selected satellites (only with
Astra1 and HOTBIRD).

If you want to run the station search independently of
the channel grid, select

frequency search

for the search

method.

The symbol rates are specified by the satellite provider
and do not normally need to be changed.

Select the signal source from a list, the station of which is to
be at the top of your station list (starting with station slot 1).
Recordings with automatic time control (see page 55) are
only possible for the respective first DVB signal source.

Initial installation

Explanations of the setting possibilities, including the upgradeable
satellite reception:

Decide how energy efficiently you want to operate your
TV set. The value for the contrast (and thus the brightness
of the background lighting) is adapted and the automatic
dimmer activated or deactivated (see page 22) depending
on the presetting.

Eco standard:

The emphasis for home use is on low energy consump-
tion. The automatic dimmer is activated.

Premium mode:

This mode optimises the settings to a brighter environ-
ment at a higher energy consumption. The automatic
dimmer is activated.

Shop mode:

The picture settings are aligned to operation in the presen-
tation room. The automatic dimmer is deactivated. If the
ambient brightness diminishes, the energy consumption
is not reduced.
The presetting can be changed later in the

TV menu

under

Picture

Picture adjustment

Presettings

(see page 22)

or under

Settings

Energy efficiency

Select the country for country-specific pre-settings.
If UK or IRL is selected for the location of TV set, it is
possible to activate MHEG-5 (UK Freeview) for the TV set.
A dialogue appears, where you can confirm to set the
operating software to the selected location.
If

Yes

is selected and confirmed with

, the TV set turns

off and on again automatically. First installation starts
again after activating the operation software.
If MHEG-5 was activated, DVB-C and DVB-S can not be
used anymore. Only terrestrial/cable and DVB-T stations
are available.

Antenna/cable (analogue):

analogue stations via

cable/antenna

DVB-T:

digital terrestrial stations

DVB-C:

digital stations via cable

DVB-S (cable 1):

digital stations via satellite

DVB-S (cable 2):

digital stations via satellite

You can preset the desired languages and reserve lan-
guages for subtitles and audio for DVB programmes
here (see page 42).

In various countries, digital stations (DVB-T, DVB-C) are
transmitted with a preset channel number per station,
known as “Logical Channel Numbers“ – “LCN“. In this
case the preset channel numbers are adopted as station
memory locations and the stations of the preferred signal
source sorted according to LCN. There may be gaps in
the numbering of the station list depending on the LCN.

Logical

Channel
Number

(continued)

Encrypted

stations

DVB-T:

Antenna

DVB-C:

Settings

DVB-S:

Satellite

system