Lockly LCK-PGD688FSN Скачать руководство пользователя

Страница: 25 / 28

FCC Warning

：

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NOTE 1:

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

NOTE 2:

Any changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement

The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for an uncontrolled

environment. It should be installed and operated with minimum distance 20cm between the radiator

& your body.

IC WARNING

This device contains licence-exempt transmitter(s) that comply with Innovation,Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Содержание LCK-PGD688FSN





























Результаты поиска

Содержание LCK-PGD688FSN

Отзывы:

Похожие инструкции для LCK-PGD688FSN

Бренды по названию

Популярные бренды

Lockly LCK-PGD688FSN, Руководство по установке

Результаты поиска

Содержание LCK-PGD688FSN

Отзывы:

Похожие инструкции для LCK-PGD688FSN

Бренды по названию

Популярные бренды