Lochinvar POWER DIRECT VENTED GAS MODELS Скачать руководство пользователя страница 33

Страница: 33 / 36

These guidelines should be utilized by a qualifi ed service agent. When calling for service notify the service agent

that this is a “Flammable Vapor Ignition Resistant” Product.

PROBLEM

CAUSE

SOLUTION

NOT ENOUGH OR

NO HOT WATER

1. Blower will not run.

A) "ON/OFF" control switch turned off.

Turn switch to the "ON" position.

B) Blower unplugged.

Plug blower back into 115 vac. outlet.

C) No power at outlet.

Repair service to outlet.

D) Thermostat defective.

Replace thermostat.

E) Control harness defective.

Replace control harness.

F) High limit control circuit open.

Replace ECO.

G) Blower motor defective.

Replace blower assembly.

3. Thermostat

problems

A) Thermostat set too low.

Turn temperature control higher.

B) Thermostat or ECO defective.

Replace thermostat or ECO as required.

4. Others

A) Heater undersized.

Reduce hot water use.

B) Low gas pressure.

Contact dealer.

C) Incoming water is unusually cold.

Allow more time for heater to reheat.

D) Leaking hot water pipes or fi xtures.

Have plumber check and repair leaks.

VENT PIPE DEFORMED

OR DISCOLORED

Defective air fl ow restrictor.

Take unit out of service immediately; call a service
representative.

Not enough dilution air to mix with fl ue gases in inlet elbow.

Proper dilution air must be provided for combustion and dilution of
fl ue temperature. Refer to the "INSTALLING THE NEW WATER
HEATER" section in the manual.

Dilution air too hot for mixing with fl ue gases.

Supply air is too hot. Check for heat sources around intake
terminal and blockage of dilution air leg.

Wrong burner orifi ce.

Install correct orifi ce.

YELLOW FLAME

Dirt in burner ports.

Turn off heater and gas, clean burner head.

Combustion air path restricted.

Check intake venting arrangement for obstructions.

Not enough dilution air for proper combustion.

Check intake venting arrangement for obstructions.

CONDENSATION

Water on the fl oor under heater.

See "CONDENSATION" section.

Water dripping from blower assembly.

Provide drip "TEE" to catch condensation from horizontal section
of exhaust vent close to blower assembly.

WATER LEAKS

Improperly sealed hot or cold supply connections, relief
valve, drain valve or thermostat threads.

Tighten threaded connections.

Leakage from other appliances or water lines.

Inspect other appliances near water heater.

Condensation of fl ue products.

See "CONDENSATION" section.

LEAKING T & P VALVE

Thermal expansion in closed water system.

Install thermal expansion tank (DO NOT plug T & P valve).

Improperly seated valve.

Check relief valve for proper operation (DO NOT plug T & P
valve).

HOT WATER ODORS (Refer to

CATHODIC PROTECTION)

High sulfate or mineral content in water supply.

Drain and fl ush heater thoroughly then refi ll.

Bacteria in water supply.

Chlorinate water supply.

WATER TOO HOT

Thermostat set too high.

Refer to "TEMPERATURE REGULATION" section.

WATER HEATER SOUNDS

SIZZLING - RUMBLING

Condensation dripping on burner.

See "CONDENSATION" section.

Sediment at bottom of heater tank.

Clean sediment from tank. Refer to "DRAINING" instructions in
the "MAINTENANCE" section.

SOOTING

Improper combustion.

Refer to the "COMBUSTION AIR AND VENTILATION"
section.

HEATER LIGHT GOES OUT

IN 4–5 SECONDS

Outlet polarity is reversed.

Test polarity and correct.

VENT GAS ODORS

Lack of air supply.

Immediately shut down the water heater and contact a service
agency to determine cause.

Improperly installed vent piping.

Downdraft.

Poor Combustion.

TROUBLESHOOTING GUIDELINES

Содержание POWER DIRECT VENTED GAS MODELS





































Результаты поиска

Содержание POWER DIRECT VENTED GAS MODELS

Отзывы:

Похожие инструкции для POWER DIRECT VENTED GAS MODELS

Бренды по названию

Популярные бренды

Lochinvar POWER DIRECT VENTED GAS MODELS, Инструкция по эксплуатации

Результаты поиска

Содержание POWER DIRECT VENTED GAS MODELS

Отзывы:

Похожие инструкции для POWER DIRECT VENTED GAS MODELS

Бренды по названию

Популярные бренды