background image

66

            

Installation & Operation Manual

11  

Operating information 

Monitor external limits

Connections are provided on the connection board for 
external limits such as flow switch, low water cutoff, gas 
pressure switches, and a louver proving switch.  The SMART 
SYSTEM will shut off the burner and inhibit relighting 
whenever any of these external limits open.

Run-time and alarm outputs

The boiler provides dry contacts for indicating when the 
boiler is running, and when it is unable to operate.

Run-time and cycle counting

The control uses two timers to monitor the total hours of 
burner operation.  One timer monitors the time the boiler is 
firing in the Space Heating Mode.  The other timer monitors 
the time the boiler is in the DHW Mode.

The control uses two (2) ignition counters to monitor the 
amount of boiler cycles.  The first counter counts all ignitions 
of the control.  The second counter counts only ignition 
attempts that have failed.  

Service reminder

The control can be programmed for service reminder 
notification.  This notification will become active when either 
a set time frame has expired, or a set amount of running 
hours or cycles has expired (all adjustable by the installer).  
The display will show a Maintenance Required screen.  The 
installer's name and phone number can be programmed into 
the control.  This information will appear on the Maintenance 
Required screen.  The service reminder notification can be 
reset or disabled by the installer.

Error logging

The control will hold in memory the last 10 lockouts as 
well as the last 10 blockings.  The date and time of the 
occurrence will be recorded as well.  Only the 10 most current 
occurrences of each will be held in memory.

Boiler temperature regulation

Operating temperature (target)

The SMART SYSTEM control module senses water 
temperature and regulates boiler firing and firing rate to 
achieve a target temperature.  The target temperature can be 
set between 32°F and 190°F.

•   Target temperature is fixed when the outdoor 
 

sensor is not installed.

•   Target temperature is calculated as described in 
 

this section under “Outdoor Reset Operation” and 

 

“Target Temperature Boost” when the outdoor 

 

sensor is connected.  

High limit operations

The Knight wall mount is equipped with adjustable automatic 
reset and manual reset high limits.  The automatic reset high 
limit has a maximum set point of 200°F and the manual reset 
high limit has a maximum set point of 210°F.

When the outlet temperature exceeds 200°F, the automatic 
high limit action occurs.  The boiler shuts down until the outlet 
water temperature cools below 190°F, and a 60 second timer 
has expired.  If the outlet temperature continues to increase, the 
manual reset high limit action will occur at 210°F.

High limit test procedure

1.  Turn ON the main power to the boiler by placing the 
 

ON/OFF switch in the ON position.

2.  From the Status Screen, press the NAVIGATION dial to 
 

access the Set Points Screen.

3.  Press the LEFT SELECT (LIMITS) key.
4.  Select the manual reset high limit (MRHL) by rotating 
 

the NAVIGATION dial counterclockwise, then press 

 

the NAVIGATION dial.

5.  Decrease the set point of the MRHL to below the current 
 

outlet temperature (or to its minimum setting, whichever 

  is higher) by turning the NAVIGATION dial 
 counterclockwise.
6.  Press the RIGHT SELECT [SAVE] key.
7.  Press the RIGHT SELECT [HOME] key.  The new 
 

parameter will upload to the control.

8.  If the current outlet temperature is above the new MRHL 
 

set point, the MRHL will function causing boiler lockout.  

 

If this occurs, skip to Step 11.

9.  If the current outlet temperature is below the new MRHL 
 

set point, locate the pinhole (SERVICE button) below the 

 

RESET button on the display board.  Insert a thin probe 

 

(such as a paper clip) into the hole and press the button 

 

continuously for five (5) seconds to place the boiler into 

 

Service Mode.  In Service Mode, the boiler will fire at 

 

ignition speed and will then modulate up to full fire.

10.  Once the outlet temperature rises up to the MRHL set 
 

point, the MRHL will function, causing the boiler to shut 

 

down and lock out.

11.  Repeat Steps 2, 3 and 4.
12.  Set the MRHL to the appropriate set point by turning the 
 

NAVIGATION dial clockwise.

13.  Repeat Steps 6 and 7.
14.  Press the RESET button to clear the lockout.  
15.  If needed, press the RIGHT SELECT [STOP] key to exit 
 Service 

Mode.

Please note that the brackets ([]) denote 
screen status.

 NOTICE

Содержание Knight 399

















































































Отзывы: