background image

7

        

Dual Fuel Supplemental Manual

 WARNING

Do not check for gas leaks with an open 
flame -- use the bubble test.  Failure to 
use the bubble test or check for gas leaks 
can cause severe personal injury, death, or 
substantial property damage.

14.  Turn on the gas supply at the manual gas valve.

15.  Turn the power switch to the “ON” position.

16.  Adjust the temperature set point on the control panel of 
 

the SMART TOUCH control module to the desired 

 

water temperature so the appliance will call for heat.

17.  Check burner performance by cycling the system while 
 

you observe burner response.  The burner should ignite 

 

promptly.  Flame pattern should be stable.  Turn system 

 

off and allow burner to cool, then cycle burner again to 

 

ensure proper ignition and flame characteristics.

18.  Repeat Steps 1 - 17 for both natural and LP gas supply.

Ignition problems are especially noticeable in NEW LP 
installations and also in empty tank situations.  This can 
also occur when a utility company shuts off service to an 
area to provide maintenance to their lines.

Gas valve replacement

The gas valve MUST NOT be replaced with a 
conventional gas valve under any circumstances.  As 
an additional safety feature, the  gas valves have flanged 
connections to the venturis and blowers.

Figure 1-1 Inlet Gas Supply Check_Natural

DIR #2000508192

DO NOT adjust or attempt to 
measure gas valve outlet pressure. 

 

Attempting to alter or measure 
the gas valve outlet pressure could 
result in damage to the valve, 
causing potential severe personal 
injury, death, or substantial property 
damage.

Failure to follow all precautions 
could result in fire, explosion, or 
death!

 WARNING

 WARNING

1  

Gas connections 

(continued)

     

Gas Pressure

The gas pressure must remain between 4 inches w.c. (.99 kPa) 
minimum and 14 inches w.c. (3.5 kPa) maximum for Natural 
gas and between 4 inches w.c. (.99 kPa) minimum and 14 
inches w.c. (3.5 kPa) maximum for LP gas during standby 
(static) mode and while in operating (dynamic) mode.  If an 
in-line regulator is used, it must be a minimum of 10 feet (3 m) 
from the Crest boiler.  It is very important that the gas line is 
properly purged by the gas supplier or utility company.  Failure 
to properly purge the lines or improper line sizing, will result 
in ignition failure.

Figure 1-2 Inlet Gas Supply Check_Propane

DIR #2000508193

Содержание Crest 1251

















Отзывы: