LNS TRYTON 112 Скачать руководство пользователя страница 71

Страница: 71 / 103

7 - 8

CHAPTER 7 : GENERAL DESCRIPTION

TRYTON 112 CNC

5.2

Operation

Please read the safety precautions described at the beginning of this manual
before handling the following devices.

Conditions :

- Feeder in MAN or STOP position
- No bar between the feeder and the lathe
- Pusher inside the feeder
- The area around the bar-feeder must be clear

Procedure :

Raise the support arm (A).

Push the arm against the stop so that it is resting on its support

Attention :

if the arm is not placed correctly, the bar-feeder may fall causing
considerable physical and material damage.

Loosen the lever (B) and unscrew
until the screw is free.

Pivot the feeder.

When maintenance operations are
finished, bring the bar-feeder back to
the working position.

Resecure with the lever (B) then bring
the support arm (A) down again.

Содержание TRYTON 112








































































































Результаты поиска

Содержание TRYTON 112

Отзывы:

Похожие инструкции для TRYTON 112

Бренды по названию

Популярные бренды

LNS TRYTON 112, Инструкция по эксплуатации

Результаты поиска

Содержание TRYTON 112

Отзывы:

Похожие инструкции для TRYTON 112

Бренды по названию

Популярные бренды