Livorsi TTK1050EM Скачать руководство пользователя страница 1

Страница: 1 / 12

Trim Tab Installation with Electronic Sensors

Model Number: TTK750EM, TTK850EM, TTK950EM,

TTK

1050

, TTK1150EM

Parts Included

(2) Trim Tabs with Sensors

(2) Hydraulic Pumps

(2) Mounting Templates

Harnesses - TTMWH & (2) - TTIWH

Mounting Hardware

Stainless steel hoses sold separately- 2 hoses required per tab

Mounting Tab Location

Available mounting area:

Before selecting a mounting location verify proper clearances inside (transom mounted compo-

nents, etc) and outside (turning drive and propeller clearance) of the boat.

Do not

mount tabs

in the chine area.

NOTE:

The farther the tabs are between each other the better, this will allow you to achieve

the maximum performance out of your tabs.

1 of 12

LIT-TTE

M-INST

REV A

ECO 28610

715 Center Street

Grayslake IL 60030

P: 847-752-2700

F: 847-752-2415

www.livorsi.com

Содержание TTK1050EM













Результаты поиска

Содержание TTK1050EM

Отзывы:

Похожие инструкции для TTK1050EM

Бренды по названию

Популярные бренды

Livorsi TTK1050EM, Руководство по установке

Результаты поиска

Содержание TTK1050EM

Отзывы:

Похожие инструкции для TTK1050EM

Бренды по названию

Популярные бренды