Littlebits Arduino Coding Kit, Руководство по эксплуатации

Страница: 30 / 32

24
WARNING
• This product contains small
magnets. Swallowed magnets can stick
together across intestines causing
serious infections and death. Seek
immediate medical attention if
magnets are swallowed or inhaled.
• Most modules are small parts. DO
NOT allow children under 3 years
old to play with or be near this
product.
• NEVER connect any modules or
circuits to any AC electrical
outlet.
• Do not touch or hold any moving
parts of modules while they are
operating.
• Keep conductive materials (such as
aluminum foil, staples, paper clips,
etc.) away from the circuit and the
connector terminals.
• Always turn off circuits when not
in use or when left unattended.
• Never use modules in or near any
liquid.
• Never use in any extreme
environments such as extreme hot or
cold, high humidity, dust or sand.
• Modules are subject to damage by
static electricity. Handle with
care.
• Some modules may become warm
to the touch when used in certain
circuit designs. This is normal.
Rearrange modules or discontinue
using if they become excessively
hot.
• Discontinue use of any modules
that malfunction, become damaged
or broken.
CAUTION: Parental Supervision and
assistance may be required for use
of components
VERY IMPORTANT NOTE
• Several inventions in this Kit
involve the use of sharp objects.
These tools should be used ONLY
under direct adult supervision.
BATTERIES
• Non-rechargeable batteries are
not to be recharged.
• Rechargeable batteries are to be
removed from the product before
being charged.
• Rechargeable batteries are
only to be charged under adult
supervision.
INSTRUCTIONS
We recommend using littleBits
brand 9-volt batteries, but
standard alkaline or standard
rechargeable batteries may also be
used. Properly discard and replace
exhausted batteries.
• Do not connect the two battery
terminals to any conducting
material.
CARE AND CLEANING
Clean modules ONLY by wiping with a
dry cloth. If necessary, isopropyl
alcohol on a cloth may be used
sparingly, and then wipe with a
dry cloth.
DO NOT use any other cleaning
products on modules.
RADIO AND TELEVISION
INTERFERENCE
This device complies with the
limits for a Class B digital
device, pursuant to Part 15 of the
FCC rules. Operation is subject to
the following two conditions:
1) This device may not cause
harmful interference, and
2) this device must accept any
interference received, including
interference that may cause
undesired operation.
These limits are designed to
provide reasonable protection
against harmful interference in
a residential installation. This
equipment generates, uses and can
radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference
to radio communications. However,
there is no guarantee that
interference will not occur in
a particular installation. If
this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try
to correct the interference by one
or more of the following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation between
the equipment and the receiver.
• Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
Changes and modifications not
expressly approved by the
manufacturer or registrant of this
equipment can void your authority
to operate this equipment under
Federal Communications Commissions
rules.
GOT A QUESTION?
Visit littleBits.cc/faq for
troubleshooting and additional
support.
littleBits Electronics Inc.
601 W 26th Street, M274
NY, NY 10001
(917)464-4577
www.littleBits.cc
Released under CERN Open
Hardware License, Version 1.2
Designed By: littleBits
Electronics, Inc.
©
2016 littleBits Electronics, Inc.
All rights reserved.
Made in China
littleBits, the littleBits
logo, Bit, Bits, and bitSnaps
are trademarks of littleBits
Electronics, Inc. in the United
States, other countries, or both.
Arduino is a trademark of Arduino,
LLC.
Etch A Sketch is a registered
trademark of Spin Master Ltd.
Other company, product, and service
names may be trademarks or service
marks of others.