7
PRO EDGER
ASSEMBLY INSTRUCTIONS
Your Little Wonder Pro Edger requires a minimal amount
of assembly prior to use. Use
Figures 1 & 3
in parts sec-
tion for assembly.
1. Remove two nuts & bolts (P/N 472 & 144-1), holding
handle supports (P/N 267 & 266) to lower handle (P/N
141-2).
2. Align upper handle (P/N 142-2) with lower handle (P/N
141-2 and replace the two nuts and bolts that were
removed in step one.
3. Use two bolts & nuts (P/N 472 & 144-1) in the upper
holes of the handles - now tighten all four bolts.
4. Use a #10-32 x 1 1/4 screw and lock nut (P/N 208 &
973) to connect the upper adjusting rod (P/N 155) to
the lower adjusting rod (P/N 4163572).
5. Remove cotter pin and washer (P/N 156 & 163) from
belt slackener lever (P/N 167-2) and place elongated
loop of the draw bar (P/N 198) onto the belt slackener
lever. Place washer back on and install cotter pin
bending the legs once it is in place.
6. Remove the cotter pin (P/N 156) from the clevis pin
(P/N 170) and slide the clevis pin out of its hole. Place
the round hole of the draw bar (P/N 198) between the
two holes of the link belt slackener (P/N 169) and slide
clevis pin back in place.
7. Replace cotter pin and bend the legs.
8. Rotate the mud flap (P/N 209) out from under the
machine so that it is as far forward as possible without
touching the brush while the paving cleaner is in its
lowest position and the rubber flap is bent forward.
Tighten from underneath.
BLADE INSTALLATION
Use
Figure 2
in parts section for assembly.
1. Place one blade washer (P/N 128) on the cutter head
shaft, and up against the bearing (P/N 124). make
sure the side with the step is against the bearing and
the flat side of the washer is facing away from the
bearing.
2. Slide the Blade (P/N 129) onto the cutter head shaft.
3. Place remaining blade washer (P/N 128) on the cut-
ter head shaft. Make sure the flat side is against the
blade and the side with the step is facing away from
the blade.
4. Attach a flange nut (P/N 130) onto the shaft and
tighten..
5. Position the enclosed Blade Guard (P/N 129B-
W.17) over the blade.
6. Align the holes in the blade guard with those on the
cutter head. Secure with two hex head screws (P/N
129C), lock washers (P/N 129D), and flat washers
(P/N 163).
SET-UP INSTRUCTIONS
THROTTLE INSTALLATION
Use
Figure 1
in parts section for assembly.
1. Remove the air filter cover from the engine.
2. Use a 10mm socket to loosen the throttle lever
pivot nut.
3. Move the remote throttle lever all the way to slow
(turtle) position. Move it 1/16” - 1/8” back towards
the fast (rabbit) position.
4. Move the engine throttle lever to the slow position
(push throttle lever to the front of the edger).
5. Remove the throttle cable retaining clamp and
screw from the engine.
6. Insert the end of the throttle cable into the hole on
the engine throttle lever.
7. Place the cable-retaining clamp over the cable,
insert the screw in and pull back and tighten.
8. Replace the air filter cover.
9. The remote throttle lever should move from slow to
fast and be approximately centered in its slot.
10. If the throttle feels tight, loosen the engine throttle
lever pivot nut.
11. If the throttle does not stay where it is placed,
tighten the remote throttle lever pivot nut (P/N 410).
Содержание PRO EDGER 6232-00-59
Страница 9: ...9 PRO EDGER PARTS SECTION ...
