2
REPLACEMENT PARTS LIST
Item No.
Part No.
Description
Quantity
1
902408
Screws 8-18 x 1-1/8"
3
2
118403
Screen
1
3
101451
Volute
1
4
118442
Impeller
1
SAFETY INFORMATION
1. Follow all local electrical and safety codes, as well as the National
Electrical Code (NEC) and the Occupational Safety and Health Act
(OSHA).
2. This pump is for use with 110V AC to 120V AC, and is equipped with
an approved 3-conductor cord for your protection against shock
hazards. It should be wired with a 3-wire system, the brown lead being
the live, blue neutral, and the green/yellow wire being the ground. This
pump should be grounded while in use to protect the operator from
electric shock. The pump must be securely and adequately electrically
grounded. This can be accomplished by attaching green/yellow
conductor to a grounded metal race-way system, a properly grounded
water pipe or other suitable means. To ensure a proper ground, the
grounding means must be tested by a qualified electrician.
3. This pump is not recommended for use with flammable liquids with
low flash points such as gasoline (see warranty).
4. Do not run the pump without liquid in the pumping head; doing so will
damage the seal and shorten the life of the pump.
5. Plug unit into 115V 60Hz grounded outlet only!
6. It is anticipated the fluid handled in the end-product application will be
limited to UL Classified Metal Parts Cleaning Solvents PJQU found in
UL’s Gas and Oil Equipment Directory. These products are basically
refined petroleum distillates for use with equipment intended to clean
metal parts essentially at room temperature. They are free from
tendency to heat spontaneously and have a flash point (closed cup)
not lower than 100°F.
7. When working around solvents, caution must be used. Fire and
toxicity are the greatest hazards encountered when using solvents.
All solvents should be stored in metal containers and must be used in
metal containers. Adequate ventilation should be provided to prevent
accumulation of vapors or fumes. No solvents should be used close
to open flame or heaters with open coils. Operators should exercise
caution when exposing skin to solvents. Protective gloves could be
used to prevent extraction of natural oils from the skin, which would
caused cracking of the skin and dermatitis. For solvent handling
precautions, consult the safety data sheet (Form OSHA—20, or
equivalent) for the particular cleaning solution.
8. Always disconnect power source before working on the pump. If the
power disconnect point is out of sight, lock in the open position and
tag to prevent unexpected application of power.
9. Keep work area clean. Cluttered areas and benches invite accidents.
10. Wiping or cleaning rags and other combustible waste materials must
be placed in a tightly closed metal container and disposed of later in
the proper fashion.
11. All visitors should be kept a safe distance from the work area.
12. Make workshop tamper-proof with padlocks, master switches, or by
removing starter keys.
13. Use safety glasses. Also, use face mask or face protection to keep
liquids from splashing on your skin or eyes. Caution: Some solvents
can cause burns which can result in blindness. An eye wash solution
should be nearby and properly maintained.
LIMITED WARRANTY
THIS WARRANTY SETS FORTH THE COMPANY’S SOLE OBLIGATION AND PURCHASER’S EXCLUSIVE
REMEDY FOR DEFECTIVE PRODUCT.
Franklin Electric Company, Inc. and its subsidiaries (hereafter “the Company”) warrants that the products
accompanied by this warranty are free from defects in materials or workmanship of the Company that exist at
the time of sale by the Company and which occur or exist within the applicable warranty period. Any distribu-
tor, sub-distributor, recipient, end-user and/or consumer agrees that by accepting the receipt of the products,
the distributor, sub-distributor, recipient, end user and/or consumer expressly agrees to be bound by the terms
of the warranty set forth herein.
I. Applicable Warranty Period
The products accompanied by this warranty shall by covered by this Limited Warranty for a period of 12 months
from the date of original purchase by the consumer. In the absence of suitable proof of purchase date, the war-
ranty period of this product will begin to run on the product’s date of manufacture.
II. Instructions Applicable to this Limited Warranty
1. Consumers wishing to submit a warranty claim must return the products accompanied by this warranty
to the point of purchase for warranty consideration.
2. Upon discovery of a defect, any personal injury, property damage or any other type of resulting damage, if
applicable, shall be reasonably mitigated to the extent possible.
3. At its discretion, the Company may inspect products either at its facilities, or in the field, and after
determination of a warranty claim, will, at its option, repair or replace defective parts. Repaired or replaced
parts will be returned freight prepaid by the Company.
4. This warranty policy does not cover any labor or shipping charges. The Company shall not be liable for any
costs or charges attributable to any product testing, maintenance, installation, repair or removal, or for any
tools, supplies, or equipment needed to install, repair, or remove any product.
III. Limitations Applicable to this Limited Warranty
THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWINg:
1. Brushes, impeller or cam on models with brush-type motors and/or flex-vane impellers.
2. Any product that is not installed, applied, maintained and used in accordance with the Company’s published
instructions, applicable codes, applicable ordinances and/or with generally accepted industry standards.
3. Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, tampering,
acts of God (including lightning), acts of terrorism, acts of war, fire, improper storage or installation, improper
use, improper maintenance or repair, damage or casualty, or to an excess of the recommended maximums as
set forth in the product instructions.
4. Any product that is operated with any accessory, equipment, component, or part not specifically
approved by the Company.
5. Use of replacement parts not sold by the Company, the unauthorized addition of non-Company products
to other Company products, and the unauthorized alteration of Company products.
6. Products damaged by normal wear and tear, normal maintenance services and the parts used in connection
with such service, or any other conditions beyond the control of the Company.
7. Any product that has been used for purposes other than those for which it was designed and manufactured.
8. Any use of the product where installation instructions and/or instructions for use were not followed.
9. Products connected to voltage other than indicated on nameplate.
10. Products where the pump was exposed to any of the following: sand, gravel, cement, grease, plaster, mud, tar,
hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.) or other abrasive or corrosive substances.
11. Products in which the pump has been used to pump or circulate anything other than fresh water at room
temperature.
12. Products in which the pump was allowed to operate dry (fluid supply cut off).
13. Products in which the sealed motor housing has been opened or the product has been otherwise
dismantled by customer.
14. Products in which the cord has been cut to a length of less than three feet.
The Company reserves the right at any time, and from time to time, to make changes in the design and/or
improvements upon its product without thereby imposing any obligation upon itself to make corresponding
changes or improvements in or upon its products already manufactured and/or previously sold. The Company
further reserves the right to substitute parts or components of substantially equal quality in any warranty service
required by operation of this Limited Warranty.
This written Limited Warranty is the entire warranty authorized and offered by the Company. There are no
warranties or representations beyond those expressed in this document.
THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES INCLUDING
WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE HEREBY SPECIFICALLY DISCLAIMED AND EXPRESSLY EXCLUDED. CORRECTION
OF NON-CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME AS SET FORTH ABOVE, SHALL
CONSTITUTE FULFILLMENT OF ALL LIABILITY OF THE COMPANY TO THE PURCHASER WHETHER BASED ON
CONTRACT, NEGLIGENCE, OR OTHERWISE.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAgES
SUCH AS, BUT NOT LIMITED TO:
DAMAgE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF USE OF EQUIPMENT, FACILITIES
OR SERVICE, LOSS OF PROFIT OR SALES, COST OF PURCHASES OR REPLACEMENT gOODS, CLAIMS OF
CUSTOMERS OF THE PURCHASER, FAILURE TO WARN AND/OR INSTRUCT, LOSS OF OTHER PRODUCTS,
OR COSTS OF ENVIRONMENTAL REMEDIATION, OR DIMINUTION IN PROPERTY VALUE. THE REMEDIES
OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF THE COMPANY SHALL
NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCTS UPON WHICH
SUCH LIABILITY IS BASED. DAMAgES AS SET FORTH IN THIS PARAgRAPH SHALL BE REASONABLY
MITIgATED TO THE EXTENT POSSIBLE. THIS PARAgRAPH SHALL ALSO APPLY TO ALL DAMAgES
RESULTINg FROM CONDITIONS SET FORTH IN SECTION III ABOVE AND (1) DEFECTS IN PRODUCT
PROTOTYPES OR REPLACEMENT PART PROTOTYPES THAT HAVE NOT BEEN PUT INTO PRODUCTION,
CIRCULATED AND SOLD BY THE COMPANY, AND/OR (2) DEFECTS THAT WERE NOT FOUND AT THE TIME
OF SALE DUE TO SCIENTIFIC AND TECHNOLOgICAL REASONS.
This Limited Warranty gives you specific legal rights. You may have other rights, which vary according to the appli-
cable laws and regulations. Where any term of this warranty is prohibited by such laws, it shall be null and void, but
the remainder of this warranty shall remain in full force and effect.
DISCLAIMER: Any oral statements about the product made by the seller, the Company, the representatives or
any other parties, do not constitute warranties, shall not be relied upon by the user, and are not part of the con-
tract for sale. Seller’s and the Company’s only obligation, and buyer’s only remedy, shall be the replacement and/
or repair by the Company of the product as described above. Before using, the user shall determine the suitability
of the product for his intended use, and user assumes all risk and liability whatsoever in connection therewith.
For technical assistance, please contact . . . . . . . . . . . . . . . . . . . . . 800.701.7894
www.franklinwater.com