Littelfuse 111-Insider-P Скачать руководство пользователя страница 38

Страница: 38 / 48

Littelfuse.com/Pump-Protection

Liquid Level Protection

Sensor and Control Relays

460-15-100-LLS

Liquid Level Sensor

Description

The 460-15-100-LLS is a liquid level sensor to detect the

presence of conductive liquids. A probe is mounted at the

desired tank level and connected to the Littelfuse Pump

Protection Relay. When the probe is submersed, the relay’s

output contacts will change state as soon as the debounce time

expires. The adjustable debounce timer is intended to prevent

nuisance actuating due to waves or splashing in the tank.
Relay logic can be inverted so the relay’s output contacts change

state when the probe is no longer submersed. This makes the

unit versatile for use in pump-up and pump-down applications.

Specifications

Input Characteristics

Control Voltage

110/120VAC nominal

Frequency

50*/60Hz

Sensitivity

100kΩ

Functional Characteristics

Probe Sense Voltage

5vdc pulsed

Debounce Time Delay

2-60 seconds

Output Characteristics

Output contact Rating

– (Two Form A - SPST)

Pilot Duty

360VA @ 240VAC

General Purpose

8A @ 240VAC

General Characteristics

Ambient Temperature Range

Operating

-20° to 70°C (-4° to 158°F)

Storage

-40° to 80°C (-40° to 176°F)

Maximum Input Power

2 W

Class of Protection

IP20, NEMA 1 (finger safe)

Relative Humidity

10-95%, non-condensing per IEC 68-2-3

Terminal Torque

4.5 in.-lbs.

Wire

12-20 AWG

Standards Passed

Electrostatic Discharge (ESD)

IEC 61000-4-2, Level 3, 6kV contact, 8kV air

Radio Frequency Immunity,

Radiated

150MHz, 10 V/m

Fast Transient Burst

IEC 61000-4-4, Level 3, 3.5kV input power

and controls

Surge

IEC

IEC 61000-4-5, Level 3, 4kV line-to-line;

Level 4, 4kV line-to-ground

ANSI/IEEE

C62.41 Surge and Ring Wave Compliance to

a level of 6kV line-to-line

Hi-Potential Test

Meets UL508 (2 x rated V + 1000 V for 1 min.)

Safety Marks

cULus

UL508 (File #E68520)

IEC 60947

Enclosure

Polycarbonate

Dimensions

88.9 mm (3.5”);

52.93 mm (2.08”);

59.69mm (2.35”)

Weight

1 lb. (16 oz., 453.59 g)

Mounting Method

35mm DIN rail or Surface Mount

(#6 or #8 screws)

*Note: 50Hz will increase all delay timers by 20%)

Features & Benefits

FEATURES

BENEFITS

Unique Probe

Protection

Probes are protected from scale build up through

pulsed DC signal between the probes

Invertible relay logic

Allows flexibility to be used in pump-up and

pump-down applications

Adjustable

debounce timer

Prevents nuisance actuating caused by waves or

splashing in the tank

LED status indicators

Quick visual indicator or of relay status of trip

Содержание 111-Insider-P

















































Результаты поиска

Содержание 111-Insider-P

Отзывы:

Похожие инструкции для 111-Insider-P

Бренды по названию

Популярные бренды

Littelfuse 111-Insider-P, Руководство пользователя

Результаты поиска

Содержание 111-Insider-P

Отзывы:

Похожие инструкции для 111-Insider-P

Бренды по названию

Популярные бренды