page 3
INSTALLATION INSTRUCTIONS
YOKE MOUNT
If Yoke mount is desired, remove Knuckle and install Yoke.
To install Yoke mount
•
Remove Knuckle (B) from Fixture using 3/16” Allen wrench to remove
two 1/2” 1/4-20 Socket Cap Screws and pull Knuckle gently off cord.
• Thread cord through center hole in upper section of Yoke (D).
• Secure Yoke to housing with Socket Cap Screws removed earlier.
Tighten to min. 2.2ft-lbs (3Nm) to max. 2.5ft-lbs (3.5Nm)
Mount fixture to the desired bracketry with
3/8” bolts, lock washer, and nut
(not provided). See Figure B for template of yoke bracket hole pattern.
To adjust the tilt angle of the fixture, use 3/16” Allen wrench to loosen
the 5/8” 1/4-20” Socket Cap
screws on both sides of the yoke. While
holding weight of fixture, use a 9/64” Allen wrench to remove 3/8” #8-32
Socket Cap set screw, adjust to desired angle and reinstall set screw in
appropriate matching hole. Re-tighten screws to min. 2.2ft-lbs (3Nm) to
max. 2.5ft-lbs (3.5Nm) to secure. See Figure C.
FIXTURE PACKING LIST
Description
Quantity
A LED Light Fixture
...............................................................................1
B Knuckle
B Knuckle .............................................................................................1
C Mounting Plate .................................................................................1
D
D Yoke
Yoke .................................................................................................1
E 1/2” 8-32 Mounting screws*
1/2” 8-32 Mounting screws* .............................................................2
F Wire Nuts*
Wire Nuts* .........................................................................................3
*Contained in parts packs
Remove fixture components and parts pack.
Check to ensure all parts
are included.
Note:
Account for small parts and destroy packing material,
as these may be hazardous to children.
Features
ESXF1 P0
ESXF1 ALO ESXF2 ALO
switchable photocontrol
ON*/OFF
color temperature
3000K/4000K*/5000K
adjustable lumens
NO, 2,500* only High 5,000*
Med 3,000
Low 1,500
High 7,500*
Med 5,500
Low 3,500
Knuckle
Knuckle installed & Mounting Plate included
Yoke
not provided
sold separately
Yoke accessory included
CHOOSE SETTINGS
(OPTIONAL)
Figure A
To change settings, use a
3/16” Allen
wrench to remove the switch cover
on the side of the fixture See Figure C. Choose your settings and replace
switch cover. Tighten to min. 1.5ft-lbs (2Nm) to max. 1.8ft-lbs (2.5Nm).
*Factory setting
FIXTURE INSTALLATION
For installation to properly installed and grounded UL listed recessed or
surface mounted weatherproof junction box.
CAUTION: WIRING
Make sure power is turned off.
•
Use wire nut to connect the bare copper or green house supply
ground wire to the green fixture ground wire.
Note:
If house wiring
does not include a ground wire, consult your local electrical code for
approved grounding methods.
For proper connection, place wire nut over wires
and twist clockwise until tight.
•
Use wire nut to connect the white fixture wire to the white (neutral)
house supply wire.
•
Use wire nut to connect the back fixture wire to the black house
supply wire.
Turn on electricity at fuse or circuit breaker box and verify success of
installation.
Note: If photosensor is in ON postion, cover photosensor
window to block daylight from entering sensor and allow lights to activate
during daytime.
Turn OFF Power at circuit breaker box.
CAUTION:
Do not rely on wall switch alone to turn off power.
KNUCKLE MOUNT
Thread Mounting Plate (C) onto Knuckle (B) and tighten locknut to
secure or thread knuckle into a 1/2” NPS hole in a compatible mounting
apparatus.
Note:
Seal arm thread using Teflon tape or silicone sealant.
Refer to wiring instructions for power connection.
Make power connection, see wiring instructions
Use mounting screws (E) to secure Mounting plate to junction box.
To adjust the tilt angle of the fixture, loosen the 1/4-20 Socket Cap Screw
in the Knuckle with a 3/16” Allen wrench, rotate fixture to the desired
angle and re-tighten screw to min. 2.2ft-lbs(3Nm) to max. 2.5ft-lbs
(3.5Nm).
Figure C
color temperature switch
lumen level switch
photocontrol switch
Figure B
Switch cover
Set Screw
Socket Cap Screw
Photosensor
DRAWING NO.
A
SHEET 2 OF 4
UNLESS OTHERWISE SPECIFIED:
WEIGHT: 7.16 LBS
REV
PART NO.
DESCRIPTION
NAME
DATE
CHK BY:
DWN BY:
ENG BY:
DRAWING PREPARED IN ACCORDANCE WITH ANSI
Y14.5M-1982
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: 2
XX: .030
XXX: .015
PROPRIETARY AND CONFIDENTIAL
THIS PRINT IS THE
CONFIDENTIAL PROPERTY OF
ACUITY BRANDS AND IS
LOANED SUBJECT TO RETURN
UPON DEMAND AND UPON
EXPRESS CONDITION THAT IT
WILL NOT BE DISCLOSED TO
ANY THIRD PARTY WITHOUT THE
PRIOR WRITTEN PERMISSION OF
ACUITY BRANDS OR USED
DIRECTLY OR INDIRECTLY IN
ANY WAY DETRIMENTAL TO THE
INTEREST OF ACUITY BRANDS
THIRD ANGLE PROJECTION
DO NOT SCALE DRAWING
FINISH
MATERIAL
D
SIZE
SCALE: 1:1
A
A
B
B
C
C
D
D
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
C) Mounting Plate
A) Light Fixture
B) Knuckle
E) Mounting Screws
F) Wire Nuts
Ø0.437" [Ø11.1]
3PLACES
1.260" [32]
0.098" [2.5 ]
BRACKET THICKNESS
3.346" [85]
1.750" [44.5]
0.875" [22.2]
