LITE
POWER
POWER
DIMMABLE
TM
POWER
POWER
POWER
POWER
USER GUIDE
Standard Capacity
RATING: 8 amps max. total,
8 amps max. per channel
INPUT: 10~50VDC
OUTPUT: DynaRythmic PWM
SIZE: 76.2 mm (3 in.) width
44.2 mm(1.74 in.) height
92.7 mm (3.65 in.) length
WEIGHT: 7.44 oz, 211 g
Input voltage must match load voltage requirements!
High Capacity
RATING: 16 amps max. total,
16 amps max. per channel
INPUT: 10~50VDC
OUTPUT: DynaRythmic PWM
SIZE: 76.2 mm (3 in.) width
44.2 mm(1.74 in.) height
90.2 mm (3.55 in.) length
WEIGHT: 7.83 oz, 222 g
Input voltage must match load voltage requirements!
LiteDimmer Pro Single Specifi cations
About LiteDimmer Pro Single
LiteDimmer Pro Single is the most advanced handheld LED
dimmer on the market. It is the backbone of control for LiteGear’s
Single LED products. Single LiteRibbon® is designed with either
Tungsten or Daylite LED emitters. Its simple yet powerful approach
to controlling brightness sets a new standard of performance
and quality while allowing the kind of fl exibility demanded from
lighting professionals. LiteDimmer Pro Single is designed for
use only with LiteGear
TM
LEDs that incorporate current limiting.
LiteDimmer Pro Single is not designed to limit current. Additional
devices may be required.
Power Supply Options
LiteDimmer Pro Single is capable of operating with DC voltage
between 10VDC to 50VDC only. It will not increase or decrease
input voltage. You must provide voltage that is compatible with
the power requirements of LiteRibbon. We recommend that you
do not use LiteDimmer Pro Single with non-LiteGear LED products.
1
Controls
The dimmer is equipped with hideaway rotary controls. Pushing
the knobs into the case can protect against accidental adjustments
as well as allow for safe storage.
Connections
LiteDimmer Pro Single is available in two versions, standard and
high capacity. The standard unit is assembled with a 2.1 mm
x 5.5 mm Barrel male input connector and is capable of 8 amps
maximum. The high capacity unit includes a Phoenix-2 male
(PH2-M) input connector and can control up to 16 amps. The
standard unit features a Barrel female output connector while
the high capacity unit features a Phoenix-2 female (PH2-F) output
connector. See the rear panel for pin confi gurations.
LEVEL Knob
TRIGGER
Button
Indicator
Light
Power
Switch
Front (8A and 16A)
Safety and Maintenance
Before operation, inspect the
cables and enclosure for any
damage. Also, inspect the
installation for short circuits,
damage, water, or similar.
2
How to Install
1. Connect the load to the Barrel or Phoenix-2 output connector.
Be sure you observe current capacities of all components such
as cable, connectors, and power supplies.
2. Position the switch in the center (OFF) position.
3. Turn the “Level” knob to 0%.
4. Provide DC power between 10V and 50V to the input connector.
You are now ready to operate LiteDimmer Pro Single.
Note: Power supply voltage must match the rating of the
LiteRibbon or damage may occur.
Back (8A Only)
Power Input (Barrel)
10~50VDC
Output Connector (Barrel)
Back (16A Only)
REMOTE TRIGGER
Jack
Output Connector (PH2-F)
Power Input (PH2-M)
10~50VDC
REMOTE TRIGGER
Jack
3
Software Modes
LiteDimmer Pro Single is programmed with several advanced
software features. Moving the switch to the up (ON) position
turns the dimmer on in normal SINGLE mode. Moving the switch
down to the (ALT) position accesses one of the advanced software
features at any given time. See the next page for the available ALT
modes.
How to Change Modes
1. Place the switch in the center (OFF) position.
2. Locate the PROG button in the lower section of the front
panel, and using the included actuator tool, depress the
PROG button for approximately 2 seconds. The indicator light
will begin flashing.
3. Turn the “Level” knob until the flashing indicator shows the
color that corresponds to the desired mode.
4. Confi rm selection by depressing the PROG button again for
approximately 2 seconds.
After these steps have been completed, placing the switch in the
down (ALT) position will operate the dimmer in the selected mode.
4
PROG
Button
