Listen LR 400, Руководство по дизайну и инструкция, Страница: 77 / 84

71
Supplementary
Troubleshooting
Troubleshooting
The LT-800 has no power.
Make sure the 12 VDC power transformer is connected to a power source and is connected to the
MDFNPDUNHG´3RZHU,QSXWµ0DNHVXUHWKH32:(5EXWWRQLVSUHVVHGLQ
There is no audio or the audio level is too low.
0DNHVXUHWKDW\RXUDXGLRVRXUFHLVSURSHUO\FRQQHFWHGWR,QSXWDQGRU,QSXW7KH,QSXWRU
,QSXWVZLWFKHVPXVWEHLQWKHFRUUHFWSRVLWLRQIRUWKHDSSURSULDWHLQSXWOHYHO)RUH[DPSOHLI\RX
DUHXVLQJWKHRXWSXWRIDPL[HURQ,QSXWWKHVZLWFKVKRXOGEHLQWKHG%XSRVLWLRQ,ILWZHUHWREH
LQWKHG%XSRVLWLRQWKHOHYHOZRXOGEHWRRORZ$OVRFKHFNWKH,QSXWNQREWRHQVXUHLWLVSURSHUO\
DGMXVWHG<RXVKRXOGEHDEOHWRVHHWKH98PHWHUGHÁHFWRQ,QSXWRU,QSXWFRUUHVSRQGLQJZLWK
the input level of the audio source. You can listen to the audio source by connecting a headset to
the front panel jack and adjusting the Monitor volume control.
,IWKHOHYHORIDXGLRLQWRWKHWUDQVPLWWHULVORZDQGFDQ·WEHFRUUHFWHGXVLQJWKHOHYHOLQSXWVZLWFKHV
WKHDXGLRSURFHVVRUFDQEHWXUQHGRQWRERRVWWKHVLJQDOSDJHIRUGHVFULSWLRQRI3URFHVV0RGH
The audio is distorted.
Check to make sure you have the input level select switches in the proper position. You may be
providing too much audio level for the input stage to handle.
There is hum in the audio.
0DNHVXUH\RXKDYHSURSHUO\JURXQGHGWKHDXGLRVRXUFHWRWKH/7&KHFNWKHFRQQHFWLRQVIURP
WKHDXGLRVRXUFHWRWKH/7,I\RXFDQWU\WRXVHDEDODQFHGDXGLRVRXUFHWKLVZLOO
UHGXFHWKHFKDQFHRIFUHDWLQJKXP&RQQHFWDJURXQGZLUHIURPWKH/7WRJURXQGDQGRUWRWKH
ground of the source audio.
There is a tone.
7KH7HVW7RQHEXWWRQKDVEHHQSUHVVHGLWV/('OLJKWLVRQ3XVKWKH7HVW7RQHEXWWRQWRWXUQRIIWKHWRQH
The Audio Input 1 sounds “tinny”.
,I\RXDUHXVLQJDQXQEDODQFHGDXGLRVRXUFHPDNHVXUH3LQRQWKH;/5RUWKHULQJRQWKHõµSOXJLV
grounded .
I cannot pick up the signal on the receiver.
&KHFNWRPDNHVXUHWKHUHFHLYHUDQGWKHWUDQVPLWWHUDUHRQWKHVDPHFKDQQHO0DNHVXUHWKH/7
has an antenna connected. Ensure that the receiver has the antenna pointed upward.
I can pick up the signal on the receiver, but it sounds like it’s not tuned in.
&KHFNWRPDNHVXUHWKHWUDQVPLWWHUDQGUHFHLYHUDUHRQH[DFWO\WKHVDPHFKDQQHO,W·VDJRRGLGHDWR
ORFNWKHFKDQQHOVRQFHWKH\KDYHEHHQVHW7RORFNWKH/7SUHVVWKH83EXWWRQIRUVHFRQGV7R
Lock receiver on a channel, hold the seek for 3 seconds
7KHUHLVQRWVXIÀFLHQWUDQJH
First make sure that the receivers you are using are operating properly, then make sure that you have
DQDQWHQQDFRQQHFWHGHLWKHUWRWKHWRSRIWKH/7WUDQVPLWWHURUFRQQHFWHGWRWKHEDFNRIWKHXQLW
EXWQRWERWK7KHDQWHQQDVKRXOGEHDVKLJKDVSRVVLEOHDQGIUHHRIREVWDFOHV,QDGGLWLRQPDNHVXUH
you are using the correct antenna type for your unit. You might want to use a remote antenna
>/$5HPRWH$QWHQQD.LW0+]@WKDWFDQEHPRXQWHGRQDPDVWRUZDOO7U\XVLQJGLIIHUHQW
IUHTXHQFLHVWRÀQGRQHZLWKOHVVLQWHUIHUHQFHSOHDVHUHIHUWRGHVLJQJXLGH