background image

3

lci1.com    

 

   

574-537-8900    

 

CCD-0001763 

Rev: 08.07.18

Flow Max

 12V DC 

Fluid Pump 

by Duraself

Installation and Owner’s Manual

(For Aftermarket Application)

Resources Required

• Cordless or Electric Drill or Screw Gun
• Appropriate Drive Bits
• Cutting Implement for Tubing 
• Flexible, Reinforced Hose with 

1/2

" Minimum Inner Diameter

• Appropriate Pipe Fittings as Needed
• Four Screws to Fasten Pump to Mounting Surface
• 

15 Amp Electrical Cutoff Switch

Mounting Instructions

1. 

Pump may be located at the same level or below the 

water tank. However, if necessary, the pump may be 

positioned above the water tank since it is capable of a 

6 ft. vertical prime. Also, horizontal inlet tubing will allow 

priming to 30 ft.

2. 

Consider a dry location that allows easy access, if 

maintenance is required.

3. 

Installation space for pump should be at least 1 

cubic feet to allow for adequate ventilation and prevent 

overheating.

NOTE: 

Excessive heat may trigger the integral thermal 

breaker and interrupt operation. When the temperature 

drops, the breaker will automatically reset.

4. 

Pump may be mounted in any position. However, if 

pump is mounted vertically, the pump head should be in 

the down position to avoid leakage into the motor casing 

during a malfunction.

Installation

The following guidelines should be considered to achieve 

optimum pump performance. Mount the pump with 4 

screws. In many instances, the pump is being utilized as a 

replacement pump. Adjust instructions as needed.

NOTE: 

The mounting feet are intended to isolate the pump 

from the mounting surface. Overtightening, flattening or 

use of oversized screws will reduce the ability to isolate 

vibration and noise through the lines.

NOTE: 

Always follow all local or national installation codes 

and standards.

General Installation Instructions

1. 

Solid surface should be available for mounting to prevent 

vibration and noise.

2. 

Accessible location away from living quarters.

3. 

Properly-sized wiring.

4. 

Proper electrical protection.

5. 

Flexible hose on inlet and outlet.

6. 

Strainer on plumbing elbows and valves near the pump.

7. 

Minimize flow restrictions in the system.

Содержание 689052

















Отзывы: