manualshive.com logo in svg

Lionel Overland Freight Express, Руководство пользователя

Поделиться
Скачать
Lionel Overland Freight Express Скачать руководство пользователя страница 21

21

Odyssey System operations

Activating the Odyssey System in the conventional environment

F

ollow these steps to activate your locomotive’s speed control in the conventional
environment.

1. Slide the Odyssey switch to the ODY position. Refer to Figure 7 on page 26 for the location of

the switch.

2. Run the locomotive at the desired speed for approximately five seconds.

3. Press and hold the 

HORN

button on the transformer.

4. While holding the 

HORN

button, increase the track voltage by at least three volts (at least a

quarter turn). 

The locomotive’s speed will increase before returning to the initial speed. At this point, speed

control is set. Increasing the throttle will not increase the speed of the locomotive; however,
decreasing the throttle will decrease the speed of the locomotive.

You may notice a slight delay between adjusting your transformer’s throttle and the
change in your locomotive’s speed as the Odyssey System works to regulate the
voltage to the motor. If you desire instantaneous response to throttle changes, turn
off the Odyssey System.

In the conventional environment, the lights in the locomotive are connected
directly to track power. To prolong the life of your lamps, do not exceed 14 to 16
volts for extended periods.

Note!

Caution!

Turning off the Odyssey System in the conventional environment

F

ollow these steps to turn off the Odyssey System in the conventional environment.

1. While the locomotive is in neutral, turn your controller up to the maximum power (no more

than 19 volts), wait one second, then press and hold the horn button.

2. While holding the 

HORN

button, slowly reduce the track voltage to approximately one-third

or one-half of the full power.

3. Release the 

HORN

button.

4. Move the locomotive in forward OR reverse. The locomotive is now out of speed control mode.

Sliding the Odyssey System switch to the NO ODY position will disable the Odyssey
System. We recommend that you keep the Odyssey System switch in the NO ODY
position unless you want to activate the locomotive’s speed control.

Note!

Содержание Overland Freight Express









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды