LinMot E1450-DS-QN-0S Скачать руководство пользователя

Страница: 23 / 27

E1400 V2 Installation Guide

13 Ordering Information

Item

Description

Art. No.

E1400-GP-QN-0S

GENERAL PURPOSE Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1779

E1430-DP-QN-0S

PROFIBUS-DP Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1786

E1450-DS-QN-0S

ETHERCAT CoE (3x400/480VAC/ 28A / 50/60Hz)

0150-2411

E1450-EC-QN-0S

ETHERCAT Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1784

E1450-IP-QN-0S

ETHERNET IP Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1782

E1450-LU-QN-0S

LinUDP Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-2494

E1450-PD-QN-0S

PROFIdrive Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-2621

E1450-PL-QN-0S

POWERLINK Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1791

E1450-PN-QN-0S

PROFINET Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1783

E1450-SC-QN-0S

SERCOS III Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1785

E1450-SE-QN-0S

SERCOS over ETHERCAT Drive (3x400/480VAC/ 28A / 50/60Hz)

0150-1899

E1400-GP-QN-1S

GENERAL PURPOSE Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2351

E1430-DP-QN-1S

PROFIBUS-DP Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2352

E1450-DS-QN-1S

ETHERCAT CoE (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2412

E1450-EC-QN-1S

ETHERCAT Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2353

E1450-IP-QN-1S

ETHERNET IP Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2354

E1450-LU-QN-1S

LinUDP Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2495

E1450-PD-QN-1S

PROFIdrive Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2622

E1450-PL-QN-1S

POWERLINK Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2355

E1450-PN-QN-1S

PROFINET Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2356

E1450-SC-QN-1S

SERCOS III Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2357

E1450-SE-QN-1S

SERCOS over ETHERCAT Drive (3x400/480VAC/ 28A / 50/60Hz / STO)

0150-2358

Accessories

Description

Art. No.

Isolated USB-RS232 converter

Isolated USB RS232 converter with config. cable

0150-2473

RS232 PC config. Cable 2.5m

For C1100/C1250/E1200/E1400/M8000

0150-2143

Isolated USB-serial converter

Isolated USB RS232/422/485 converter

0150-3120

RR01-68/100

Regeneration resistor (68R, 100W, 1000V) (X1 connector is included)

0150-3373

NF01-FN258-16-07

3-phase line filter for E1400 (up to 50m motor cable length)

0150-2359

NF01-FS34985-20-71

3-phase line filter for E1400 (up to 20m motor cable length)

0150-2746

DC01-E1400/X4/X30

Drive Connector Set for E1400-0S

0150-3452

DC01-E1400/X4/X30/X33

Drive Connector Set for E1400-1S

0150-3453

DC01-E1400/X1

Drive Connector Regeneration / Busbar

0150-3445

MC10-L/m

Drive connector power MC10-L/m for X2

0150-3382

DC01-E1400/X4

Drive Connector 24VDC & Logic

0150-3447

DC01-E1400/X30

Drive Connector Mains Supply (3x400/480VAC)

0150-3449

DC01-E1400/X33

Drive Connector Safety (-1S)

0150-3451

MC10-EMV/14-D

Shield clamp for P10 motor power cable

0150-3631

Bold items are strongly recommended accessories!

ATTENTION: The connectors have to be ordered separately and are not
included with the drive!

Use isolated USB RS232 converter for configuration!

14 International Certifications

Certifications

Europe

See chapter “15 Declaration of Conformity CE-Marking“

UL508C pending

NTI AG / LinMot

www.LinMot.com

Page 23/27

Содержание E1450-DS-QN-0S




























Результаты поиска

Содержание E1450-DS-QN-0S

Отзывы:

Похожие инструкции для E1450-DS-QN-0S

Бренды по названию

Популярные бренды

LinMot E1450-DS-QN-0S, Руководство по установке

Результаты поиска

Содержание E1450-DS-QN-0S

Отзывы:

Похожие инструкции для E1450-DS-QN-0S

Бренды по названию

Популярные бренды