LinMot E1450-DS-QN-0S Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 27

LinMot E1450-DS-QN-0S Скачать руководство пользователя страница 8

E1400 V2 Installation Guide

4 Differences between V1 Rev. E/F and V2

The V2 redesign of the E1400 drives resulted in the following changes, that might
be relevant to the customer:

•

The cooling fan is integrated into the drive (on the V1 drives it was an option)

•

The minimum distances between the drives in the cabinet is reduced

•

No double row RJ45 connectors (Ethernet, ME and CMD)

•

X19 (RS232 config connector) is now a dedicated RJ45 connector

•

X33 (STO) is now located on top of the drive and not on the front

•

X20 (Differential analog input) is now on the bottom of the drive and not on
the front

•

The motor brake (X32) is now powered by the 24VDC from X4 (X31, supply
connector for the brake is removed)

Attention:

Configuration can not be directly imported from from a V1 into a V2

drive. It has to be done manually!
If assistance is required contact [email protected].

5 IP Address Selection

The default mode for acquiring an IP address is via DHCP. If no servers respond on
the   connected   network,   the   drive   switches   to   the   IPv4   Link-Local   addressing
scheme   (also   known   as   APIPA   on   Windows   systems).   This   way   the   drive
automatically  assigns   itself   an   address   within   the   range   of   169.254.0.1   through
169.254.255.254 (Subnet Mask 255.255.0.0).
Please  note   that   this  process  can   take  up   to   a  minute  until  a  valid  address  is
assigned to the drive.

Page 8/27

www.LinMot.com

NTI AG / LinMot

®

«
...
6
7
8
9
10
...
»

Содержание E1450-DS-QN-0S




























Отзывы:

Нет отзывов