Wireless Regulatory Information
1
Wireless Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules .
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation .
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules . These limits are designed to provide
reasonable protection against harmful interference in
a residential installation . This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications .
However, there is no guarantee that interference will not
occur in a particular installation . If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and devices
• Connect the equipment to an outlet other than
the receiver’s
• Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution
: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment .
IEEE 802 .11b or 802 .11g operation of this product in the
USA is firmware-limited to channels 1 through 11 .
The device for the band 5150-5250 MHz is only for indoor
usage to reduce the potential for harmful interference to
co-channel mobile satellite systems .
Mexico Regulatory Statement
La operación de este equipo está sujeta a las siguientes
dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia,
incluyendo la que pueda causar su operación no deseada .
EAC Mark of Conformity for Russia,
Kazakhstan and Belarus
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment . This
equipment should be installed and operated with minimum
distance 31 cm between the radiator and your body .
This device and it’s antennas(s) must not be co-located
or operating in conjunction with any other antenna
or transmitter except in accordance with FCC multi-
transmitter product procedures .
Industry Canada Statement
CAN ICES-3 (B)/NMB-3 (B)
Operation is subject to the following two conditions: (1)
This device may not cause interference, and (2) this device
must accept any interference, including interference that
may cause undesired operation of the device .
For product available in the USA/Canada market, only
channel 1~11 can be operated . Selection of other channels
is not possible .
The device could automatically discontinue transmission
in case of absence of information to transmit, or
operational failure . Note that this is not intended to prohibit
transmission of control or signaling information or the
use of repetitive codes where required by the technology .
Industry Canada Radiation Exposure
Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment . This equipment
should be installed and operated with minimum distance
31 cm between the radiator & your body .
This device and it’s antennas(s) must not be co-located
or operating in conjunction with any other antenna or
transmitter except in accordance with IC multi-transmitter
product procedures .
Restrictions in the 5 GHz Band
The device for the band 5150-5250 MHz is only for
indoor usage to reduce potential for harmful interference
to co-channel mobile satellite systems .
This device has been designed to operate with an antenna
having a maximum gain of 2 .25 dBi and 2 .3 dBi at 2 .4 GHz
and 5 GHz respectively . Antenna having a higher gain is
strictly prohibited per regulations of Industry Canada . The
required antenna impedance is 50 ohms .
The maximum antenna gain (Please see the table below)
permitted (for devices in the bands 5250-5350 MHz
and 5470-5725 MHz) to comply with the EIRP limit and
because high power radars are allocated as primary users
(meaning they have priority) in 5250-5350 MHz and