www.linkayl.com
Copyright © Linkayl Technology Limited
LK-CP63X Control Panel
¢
Troubleshoo ng
09
10
—
Please read the following instruc ons carefully before installing this product
—
Installing this product must comply with the effec ve local electricity specifica ons
—
The control system must be installed by the professional
—
The main power must be cut off before wiring to ensure safe opera on
—
Addi ve maximum output power of each single channel of double channel controller
MUST NOT exceed the total rated power of the controller
—
Addi ve maximum output power of each single channel of 5 channel controller MUST
NOT exceed the total rated power of the controller, and the maximum output current of
each channel MUST NOT exceed 10A
—
Do not use metal objects to touch or cover the controller, otherwise it will affect the
remote control signal recep on
—
The maximum transmission distance of the wireless signal can reach 50 meters or more
in the open condi on
—
The distance between the controller and ground should be more than 1.5 meters
—
The distance between the controller and ceiling should be more than 0.3 meters
—
The distance between the controller and motor should be more than 1.5 meters
—
Avoid sta c interference and prevent sta c damage to electronic components
—
Please use the so wire and cable, a er installa on ensure that the cable carrier is not
affected by the longitudinal tension
—
An external sensor must use a product that is compa ble with this controller
—
Non-professionals is not allowed to disassemble the controller. If any func on is
abnormal, please contact your local dealer
.
¢
Installa on instruc on
No.
Symptom
Solu on
1
LED flashes, receiver shut down
1. Check the connec on of wires
2. Check the receiver se ng
2
LED on the transmi er is off or weak
1. Make sure the right installa on of the ba ery
2. Change the ba ery
3
The transmi er and the receiver work well,
the motor does not work
1. Check the wiring of motor
2. Make sure the motor no failure
¢
Stroke memory
—
The controller can set and memorize the opening stroke. Upon the stroke set, the
window opening signal is triggered once, the motor will run the memorized stroke one
me
—
The default memorized stroke runs for 5 minutes
—
Press both of UP /DOWN bu ons on the controller for 3 seconds, LEDs flash 3 mes and
off, successfully entered the stroke memory se ng state
—
In the stroke memory se ng state, the manual keys are forced to the con nued-run
mode, the remote control keys are forced to the inching mode
—
Select the channel(S) to be set, the default is all selected, all the channel indicators light.
Press the channel selec on key(s), the indicators light, press the channel selec on key(s)
again the indicator is off, it is deselected. The se ng is invalid without opera on in 15
seconds
—
A er the channel selected, determine the stroke that needs to be memorized by pressing
the manual key or the remote control key by moving or jogging
—
The memorized stroke can be set to one channel or any combina on of channel
—
A er the memorized strokes determined, turn on all the channel indicators for se ng the
memorized stroke. Press both of UP /DOWN bu ons on the controller for 3 seconds, LEDs
flash 5 mes and off, the memorized strokes of all channels set successfully and exit the
stroke memory se ng state, manual bu ons and remote control bu ons restored to the
original mode
—
In stroke memory se ng state, no opera on is performed within 15 seconds, LEDs flash 3
mes slowly and off, the stroke memory se ng state is automa cally exited, and the last
memorized stroke is retained
—
Stroke memory can be set repeatedly. The controller only retains the last successful
stroke value and automa cally clears the previous one
—
In stroke memory se ng state, press both of STOP /DOWN bu ons on the controller for
3 seconds LEDs flash 3 mes the memorized stroke is deleted and restored to the default
output for 5 minutes
—
When the memorized strokes of master controller and slave controller are not the same,
the master controller will run its own memorized stroke. The slave controller will run the
shorter stroke when it receives the cascade signal from the master controller
—
The memorized stroke set for each channel is retained in case the controller is powered
down or reset
—
When closing the window, the output me is 5 minutes