GENERAL
These luminaires are used where emergency
light is needed. Each luminaire must be
permanently connected to mains power
supply
.
In normal operation the
power
and
charge
indicators are ON to indicate that the
battery is charging. In case of a mains power
supply failure the
power
and the
charge
indicators turns off and the luminaire will light
the spot lamps automatically in emergency
mode. When the mains power supply is
restored the device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions
ο
n page 3.
OPERATION
When the device is powered from the mains
,
and the battery(ies) is(are) connected, the
‘power’ and ‘charge’ indicators are ON. The
‘charge’ indicator indicates the battery
charging operation.
If
it does
not li
gh
t,
probably, the batter
ies are
disconnected. If
it
does
not li
gh
t and the batter
ies are
connected, then contact the technician. The
power
indicator
confirms
the
proper
connection to the
mains
. The
TEST butto
n,
has a dual use. If pressed
instantlly
while the
device is
connected to the mains
, the device
simulates the
power interruption
,
by
lighting
the
lamps for
3
''. In th
at
way
,
we can control
the driver circuit of
the lamps
and
the
lamps as
indicated in paragraph
3 in
the text
below.
DIMMING OPTION
When the
luminaire is in emergency mode
, with
corresponding press
ing
s of the button,
we ca
n
choose
the illumination of 100%, 50%, 33%
or
turned off
, either to increase the autonomy time
or not to consume
the
battery power
unnecessarily. This option is canceled when the
network is restored.
ΑΤΤΕΝΤΙΟΝ!
!!
1. Operations for installation, maintainance or
testing must be done by authorized
personnel only
.
2.
The device must be connected to the
mains power supply through a fuse
dependent by the total amount of the line’s
power load
.
3.
It is suggested to check every month the
indication LED for battery charging, and by
pushing instantly the TEST button to check
the emergency circuit and the lamps. If the
luminaire does not light
contact the
installer.
4. It is sug
g
ested to check every 6 months
the minimum autonomy duration by
disconnecting the mains power supply.
Count the time that the lamps light and in
Page 1 from 3
WATERPROOF NON MAINTAINED EMERGENCY LUMINAIRES
Aluminum, ABS/PC, PC
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Pb)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
24h
Power indicator, battery charge indicator, TEST button
From overcharge and deep discharge
IP65
o
5 to 40 C
Up to 95%
3 years
(1
year for the battery
)
180 min
90 min
3200lm
White power LEDs
6440gr.
4250gr.
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
220-240V AC/50-60Hz
2x12V/7Ah
12V/7Ah
307 x 100 x 350 mm.
TECHNICAL CHARACTERISTICS
(
for LED MODULE Specifications see page 2)
DU239P13EGS
DU239P30EGS
13W/13.6VA
GB
LINERGY S.R.L.
VIA ALCIDE DE GASPERI, 9
ACQUAVIVA PICENA (AP) 63075 ITALY
TEL.: +39 0735 5974
FAX: +39 0735 597474
www.linergy.it [email protected]
-
ISTDUALLED_V2-R2
