LineEye LE-2500XR Скачать руководство пользователя страница 54

Страница: 54 / 140

-52-

4.2 RS-422/485 Driver Control

Select the method of controlling RS-422/485 transmission driver IC for simulation on RS-422/485 port.

Press [MENU] then touch “Interface

” -> “Measurement port: RS-422/485” -> “Driver control”. For an optional in

terface board, “OP-SB10N”, select “Measurement port: RS-530”.

2.3 Measurement Port

For standard sub-board

For optional sub-board “OP-SB10N”

Driver Control

OFF

Select this for testing RS-422 (full-duplex), X.20/21, RS-449 and V.35 using “OP-SB10N”.

Driver IC will always be in an enable state after starting test.

Manual

: When DTR (for DTE mode) or DCD (for DCE mode) is ON, the driver will be in an enable

state. And when DTR or DCD is OFF, the driver will be in disable (high impedance) state. It is

used to control the driver IC manually for Manual or Program mode.

When OP-SB10N sub board is inserted to the analyzer and "Auto line control" is checked, the driver IC

is controlled according to the state in which the DTR and DCD are automatically controlled.

When “Auto line control” is set OFF, the initial state at the start of simulation is below:

AUTO

Select “Auto” for testing RS-485 in half duplex. The driver automatically be in an enable state

during the transmission of test data, and the driver will automatically be in disable after about 1

to 3 bits is delayed (400u seconds at least) after data transmission.

Simulation mode

Initial State of TXD Driver IC

MANUAL mode

High impedance state

FLOW Mode

Enable

ECHO Mode

Enable

POLLING Mode

Enable

BUFFER Mode

Enable

PROGRAM Mode

High impedance state

Содержание LE-2500XR













































































































































Результаты поиска

Содержание LE-2500XR

Отзывы:

Похожие инструкции для LE-2500XR

Бренды по названию

Популярные бренды

LineEye LE-2500XR, Инструкция по эксплуатации

Результаты поиска

Содержание LE-2500XR

Отзывы:

Похожие инструкции для LE-2500XR

Бренды по названию

Популярные бренды