background image

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,LPWKP - GTO P/N:

 10014581  - INK:

 BLACK - MA

TERIAL:

 20 LB.

 MEAD BOND - SIZE:

 11.000”

 X 8.500”

 - SCALE:

 1-1 - SIDE 1 OF 2

SCREW ANCHORS

MOUNTING SCREWS

KEYPAD

This digital keypad is a MegaCode series of wireless radio controls designed for use with automatic garage 
door and gate operators. The MegaCode radio format provides unparalleled security with more than a million 
different codes.
In operation, the user enters their unique code on the unit’s keypad (1 to 6 digits long) and presses 
the      button to activate the door operator. For up to 30 seconds after the last activation, the keypad can 
be re-triggered by simply pressing the      button again. This allows the user to stop or reverse the opener 
quickly, without having to re-enter their code.
The keypad has built-in keypad lighting for use at night or in dark areas. The clear silicone keys are backlit 
with a soft blue glow. Press the       light button at any time to activate the keypad backlight.
To turn the overhead operator light on or off, enter the user code, then press the       light button.
The keypad lockout timer will disable the keypad after 10 activations. The keypad must remain idle for 30 
seconds before new attempts.
MegaCode receivers are programmed by sending a signal from the user’s transmitters. This stores the 
transmitter’s code into the receiver’s memory. The receiver will retain its memory even without power and 
will only activate from these “memorized” transmitters. Each keypad code can be considered a different 
transmitter. Each MegaCode receiver can remember a maximum of 10 transmitter codes. Any combination of 
portable transmitters and keypad codes up to the maximum number can be entered.

 COMPONENTS

 KEYPAD FEATURES

   PROGRAMMING OPERATORS                     

 WALL MOUNTING

KEYPAD OPERATION

CHANGING BATTERIES

LIMITED WARRANTY

This product is warranted to the consumer against defects in material and workmanship for 

one year from the date of purchase. This warranty applies to first retail buyers of new devices. 

Warrantor will repair, or at its option, replace, any device it finds that requires service under this 

warranty, and will return the repaired or replaced device to the consumer at the warrantor’s cost. 

For warranty service and shipping instructions contact warrantor at the address shown below. 

Devices must be sent to warrantor for service at owner’s expense. The remedies provided by 

this warranty are exclusive. Implied warranties under state law are to the one year period of this 

written warranty. Some states do not allow limitations on how long an implied warranty lasts, so 

the above limitation may not apply to you. In order to be protected by this warranty, save your 

proof of purchase and send copy with equipment should repair be required. This warranty gives 

you specific legal rights, and you may also have other rights which vary from state to state.
All products returned for warranty service require a Return Product Authorization Number (RPA#). 

Contact Linear Technical Service at 1-800-543-1236 for an RPA# and other important details.

WARNING:

 Changes, modifications or adjustments not expressly approved by GTO Access 

Systems, LLC could void the user’s authority to operate this equipment. There Are No User 

Serviceable Parts.

NOTICE:

 

This device complies with part 15 of the FCC rules and with Industry Canada license-exempt RSS 

standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, 

and (2) this device must accept any interference, including interference that may cause undesired operation 

of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de 
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouil-
lage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d’en compromettre le fonctionnement.

 DESCRIPTION

Digital Keypad
Operation Instructions

LPWKP

MOUNT THE KEYPAD IN CLEAR VIEW OF THE 

DOOR WITH THE TWO SCREWS SUPPLIED

Use screw 

anchors if 

required.

Slide battery cover open and remove batteries to

access mounting hole. Replace batteries and slide

battery cover closed after mounting.

DOOR OPERATION

1

2

OVERHEAD LIGHT OPERATION

ENTER USER KEYPAD CODE

PRESS

NOTE:

 PRESS        BUTTON TO TURN KEYPAD 

BACKLIGHT ON FOR NIGHTTIME OPERATION

NOTE:

 TO STOP OR REVERSE THE OPENER, THE         

BUTTON CAN BE PRESSED AGAIN FOR UP TO 30 

SECONDS WITHOUT RE-ENTERING THE CODE

NOTE:

 THE OVERHEAD LIGHT CANNOT BE OPERATED 

FROM THE KEYPAD UNLESS THE DOOR IS OPEN

1

2

ENTER USER KEYPAD CODE

PRESS

Refer to the instructions provided with the garage door opener 

to set it into “learn” mode. 

Press the opener’s LEARN BUTTON for 1 second and release.
The opener should BEEP and the LIGHT should BLINK once.
The RED LED will remain lit in Learn Mode for 15 seconds.
While the RED LED is lit, enter a 1-6 digit code into the 
keypad. Then PRESS and HOLD the keypad’s       key until 
the opener BEEPS and the light BLINKS once.

1

2

Repeat Steps 1 & 2 for any additional keypad codes.

Printed in China for GTO Access Systems, LLC.

Copyright© 2017 GTO Access Systems, LLC

Document Number: 10014581 REV B (06-19-17)

To delete a keypad code that you no longer want follow the 

same steps above. The opener will recognize the code and 

delete it from memory. The RED LED and LIGHT will blink 4 

times to show the code was successfully deleted.

DELETING A KEYPAD CODE

HINGED COVER
PROTECTS THE KEYPAD

SOFT BLUE LIGHTS ILLUMINATE 
THE KEYS FOR NIGHTTIME USE.
PRESS LIGHT BUTTON TO ACTIVATE

ENTER USER CODE AND PRESS LIGHT
BUTTON TO TURN THE
OVERHEAD OPERATOR LIGHT ON OR OFF

      BUTTON STAYS ACTIVE FOR 30 
SECONDS AFTER A CODE IS USED SO THE 
OPENER CAN BE STOPPED OR REVERSED

TEN KEYS ENTERING 1-6 KEYPAD CODES
USING NUMBERS OR LETTERS

PRESS THE

LEARN BUTTON

THE RED LED WILL

GLOW FOR 15 SECONDS

1

ENTER A 1-6 DIGIT CODE

WHILE RED LED IS ON

2

3

INSTALL 3 FRESH
AAA BATERIES

4

SLIDE BATTERY 
COVER CLOSED

1

2

SLIDE BATTERY 
COVER OPEN

REMOVE THE OLD 
BATTERIES AND 
DISPOSE OF THEM 
PROPERLY

GTO Access Systems, LLC

(850) 575-0176

USA & Canada (800) 543-4283

www.gtoaccess.com

Follow the steps in the diagram and use caution to keep batteries away from 

children. 

Replace old batteries with fresh AAA Alkaline batteries.

Properly dispose of old batteries. 

Many electronic stores and supermarkets have battery recycling bins.

Alkaline batteries can be safely disposed of with normal household waste. 

Never dispose of batteries in fire because they could explode.

PRO ACCESS

TM

Отзывы: