User Manual
English
Introduction
Thank you for purchasing the LINDY 4K HDMI 2.0 6x2 Matrix with remote control. This high performance HDMI 2.0
Matrix allows any of the attached six sources to be shown on any of the two displays simultaneously.
It supports resolutions up to Ultra HD 2160p60 with YCbCr 4:2.0 8bpc and 2160p30 with YCbCr 4:4.4 12bpc. It
supports HDCP 2.2, as well as all Full HD 3D Formats.
At resolutions up to Full HD the PiP-Feature can display and let select all input signals in small PiP overlay windows
in the recently selected picture.
ARC (Audio Return Channel Signal) is supported on Output A.
An Infra-red remote control is supplied to make switching between sources and displays easier.
Package Contents
HDMI 6x2 4K Matrix
Mounting brackets and screws
5V DC ~2A PSU with 4 Multi Country adapters
Remote control including battery
This manual
Features
Supports display resolutions up to Ultra HD 4Kx2K 2160p60 with YCbCr 4:2.0 8bpc and 2160p30 with YCbCr
4:4.4 12pc,1080P@120Hz, and 1080P 3D@60Hz
Supports HDMI 2.0 and HDCP 2.2 Content Protection
Supports PiP (Picture in Picture) for resolutions up to Full HD 1080p
3D video support for all 3D formats
Supports audio pass through conforming to the HDMI specification 1.4 such as LPCM at up to
192kHz,compressed audio (IEC 61937), DSD, DST, DTS and HBR, High Definition lossless audio / Dolby
TrueHD DTS-HD Master Audio 7.1CH
Audio OUT and ARC function and Audio EDID Settings 2.0CH / 5.1CH / 7.1 CH
The Audio ports always refer to the signals on channel OUTPUT A
To get analogue audio signal on the 3.5mm port audio EDID must be set to 2.0CH (= analogue audio)
When ARC is on the audio ports will always use the ARC signal as provided from the TV connected to
OUTPUT A – otherwise the audio is extracted from the selected INPUT signal to OUTPUT A
Specifications
Input Ports: 6 x HDMI Female type A
Output Ports: 2 x HDMI Female type A
Power Supply: 100…240VAC / 5V DC ~2A
Dimensions: 26 x 12 x 3 cm (WxDxH)
Operating temperature range 0°C ~ 40°C
Storage temperature range: -20°C ~ 60°C
Relative Humidity: 20 ~ 90% RH (Non-condensing)
For indoor use only
Power Consumption: 10W max.
User Manual
English
Operation
Front Panel
1.
ON/OFF: Power on/off switch
2.
INPUT LED: These LED’s will illuminates when a source device is connected with a power supply
3.
EDID LED: The LED will illuminate when you select the channel
4.
ARC LED: The LED will illuminate when the ARC function is selected
5.
POWER LED: The LED illuminates when the device is connected with a power supply and switched on
6.
OUT A BUTTON: Press this button to select the source for output A
7.
OUT B BUTTON: Press this button to select the source for output B
8.
EDID BUTTON: Press this button to select the audio output mode
9.
ARC BUTTON: Press this button to select the ARC function
10. RST BUTTON: Press this button to reset back to factory defaults (Input 1, 2.0CH Audio, ARC off)
11. IR IN: Remote control signal receive window
Rear Panel
1.
HDMI INPUT: Connect your HDMI source to these ports with HDMI cables
2.
HDMI OUTPUT: Connect your HDTV or monitor to these ports with HDMI cables
3.
STEREO OUT:** Connect your switch to an amplifier using a 3.5mm jack cable
4.
TOSLINK OUTPUT:** Connect your switch to an amplifier using optical fibre
5.
DC IN: Plug the 5V DC power supply into the unit and connect the adapter to an AC wall outlet
* Port 6 will support MHL input using an active MHL cable.
** The audio out will always take the audio from the HDMI A output port.
Remote control
Power button: Power the switch on or off
Audio: Pressing this button will toggle the audio output mode,, the front LED will
indicate the current option selected
ARC:*** Press this button to active or deactivate ARC
PiP: When pressing the PiP button, the image on OUTPUT B will mirror the image
on OUTPUT A
Select: Pressing this button will scroll through the PiP source
Enter: Once you have found the PiP source you want to watch, press enter to show
this on the full screen for both OUTPUT A and B
*** To use the ARC function, your TV must support ARC and must be connected to
output A. When ARC is not selected, the switch will output the audio from the selected input source. When ARC is
selected the ARC return signal from the TV will be used.
The analogue 3.5mm Audio port will only output a signal when the HDMI signal contains uncompressed Audio like
LPCM – audio EDID must be set to 2.0CH. If it is set to Dolby, DTS, 5.1 or 7.1 or any other compressed signal
audio will not be output via the 3.5mm port.
