Lincoln INVERTEC V350-PRO CE Скачать руководство пользователя

Страница: 6 / 38

SAFETY

V350-PRO (CE)

L10093

3-1-96H

Conformance

standard: EN 50 199 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It

All electrical equipment generates small amounts of electromagnetic emission. Electrical emission may be

received by other equipment, electrical interference may result. Electrical emissions may affect many kinds of

telephone systems, computers, etc. Be aware that interference may result and extra precautions may be required

If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment

to resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may

electromagnetic disturbances must be reduced to the point where they are no longer troublesome.

assess whether the changes will increase the risk of injury, e.g., by allowing parallel welding

surrounding area. The following shall be taken into account:

welding equipment;

b) radio and television transmitters and receivers;

d) safety critical equipment, e.g., guarding of industrial equipment;

e) the health of the people around, e.g., the use of pacemakers and hearing aids;

f) equipment used for calibration or measurement;

used in the environment is compatible. This may require additional protection measures;

ELECTROMAGNETIC COMPATIBILITY (EMC)

Products displaying the CE mark are in conformity with European Community Council Directive of 3 May

1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility

(89/336/EEC). It was manufactured in conformity with a national standard that implements a harmonized

is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.

Introduction

transmitted through power lines or radiated through space, similar to a radio transmitter. When emissions are

electrical equipment; other nearby welding equipment, radio and TV reception, numerical controlled machines,

when a welding power source is used in a domestic establishment.

Installation and Use

The user is responsible for installing and using the welding equipment according to the manufacturer s instructions.

be as simple as earthing (grounding) the welding circuit, see Note. In other cases it could involve constructing an

electromagnetic screen enclosing the power source and the work complete with associated input filters. In all cases

Note: The welding circuit may or may not be earthed for safety reasons according to national codes.

Changing the earthing arrangements should only be authorized by a person who is competent to

current return paths which may damage the earth circuits of other equipment.

Assessment of Area

Before installing welding equipment the user shall make an assessment of potential electromagnetic problems in the

a) other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the

c) computer and other control equipment;

g) the immunity of other equipment in the environment. The user shall ensure that other equipment being

h) the time of day that welding or other activities are to be carried out.

Содержание INVERTEC V350-PRO CE







































Результаты поиска

Содержание INVERTEC V350-PRO CE

Отзывы:

Похожие инструкции для INVERTEC V350-PRO CE

Бренды по названию

Популярные бренды

Lincoln INVERTEC V350-PRO CE, Руководство оператора

Результаты поиска

Содержание INVERTEC V350-PRO CE

Отзывы:

Похожие инструкции для INVERTEC V350-PRO CE

Бренды по названию

Популярные бренды