manualshive.com logo in svg

Lincoln Countertop Impinger, Руководство по обслуживанию

Поделиться
Скачать
Lincoln Countertop Impinger Скачать руководство пользователя страница 46

 

 

CounterTop – 1300 Series Service Manual 

46 

THERMOSTAT, OVEN CAVITY HI-LIMIT 
 

1.  Remove control box cover. 
2.  Remove oven back assembly. (See OVEN BACK) 
3.  Remove two (2) wires from thermostat. 
4.  Remove retaining nut from the front of thermostat and remove thermostat. 
5.  Remove capillary tube from wire form in back of oven and remove assembly out through control box side. 
6.  Reassemble in reverse order.  Check for proper routing through insulation.  Be sure capillary tube is held 

securely in the wire form and the reset button has been pushed in and set. 

NOTE

: All excess capillary tubing should be brought back into control box area.  Be certain to replace 

insulation seal when oven back is re-installed. 

7. Check 

operation. 

 

AIR PRESSURE SWITCH – REPLACEMENT (S/N 3043630 and below) 
 

1.  Remove control box cover. 
2.  Remove two (2) wires. 
3.  Remove air tube (note location). 
4.  Remove four (4) screws and replace air switch. 
5.  Reassemble in reverse order and check operation. 

NOTE:

 Make sure to use rubber grommets when installing air switch. 

 

ADJUSTMENT SCREW

 

 
 

AIR PRESSURE SWITCH – ADJUSTMENT (S/N 3043630 and below)

 

 

1.  Apply power to oven, turn temperature control potentiometer to max. and allow 30-minutes preheat for 

temperatures to stabilize. 

2.  Remove air tube and with a volt meter verify that contactor for heater elements opens. 
3.  WITH POWER ON: Re-connect tube and check voltage across the air switch making sure that there is 

no voltage drop and it remains steady.  Adjust as needed. (See Picture, verify adjustment screw has not 
vibrated out). 

NOTE

: Allow 30 minutes preheat. 

 

THERMOSTAT, CONTROL BOX HI-LIMIT 

 

1.  Remove control box cover. 
2.  Remove two (2) wires. 
3.  Remove two (2) screws and replace 
4.  Reassemble in reverse order and check operation.   

NOTE

:  Make sure reset button has been pushed and set. 

 
 
 

 

Содержание Countertop Impinger

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды