Lincoln 1997 Town Car Скачать руководство пользователя | Manualshive

Страница: 239 / 305

background image

237

Treadwear

The treadwear grade is a comparative rating based
on the wear rate of the tire when tested under
controlled conditions on a specified government test
course. For example, a tire graded 150 would wear
one and one-half (1 1/2) times as well on the
government course as a tire graded 100. The
relative performance of tires depends upon the
actual conditions of their use, however, and may
depart significantly from the norm due to variations
in driving habits, service practices and differences in
road characteristics and climate.

Traction A B C

The traction grades, from highest to lowest, are A,
B, and C, and they represent the tire’s ability to
stop on wet pavement as measured under controlled
conditions on specified government test surfaces of
asphalt and concrete. A tire marked C may have
poor traction performance.

WARNING

The traction grade assigned to this tire
is based on brakinig (straightahead)
traction tests and does not include
cornering (turning) traction.

Temperature A B C

The temperature grades are A (the highest), B, and
C, representing the tire’s resistance to the
generation of heat and its ability to dissipate heat
when tested under controlled conditions on a
specified indoor laboratory test wheel. Sustained
high temperature can cause the material of the tire
to degenerate and reduce tire life, and excessive
temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance
which all passenger car tires must meet under the
Federal Motor Vehicle Safety Standard No. 109.
Grades B and A represent higher levels of
performance on the laboratory test wheel than the
minimum required by law.

File:11fnmct.ex

Update:Mon Jun 17 13:54:56 1996

«
...
237
238
239
240
241
...
»

Содержание 1997 Town Car


















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1997 Town Car

Бренд: Whispbar Страницы: 77

Бренд: muth Страницы: 10

Hypercharger HYC 075

Бренд: Alpitronic Страницы: 64

1506-PHX Cargo Plus

Бренд: Ranger design Страницы: 8

Бренд: AUTOTECH Страницы: 1

1500 CLASSIC 2020

Бренд: RAM Страницы: 360

Бренд: Kargo Master Страницы: 18

Бренд: Quadratec Страницы: 2

Бренд: Honda Страницы: 326

Бренд: Honda Страницы: 279

Бренд: Kia Страницы: 25

Rear Observation System Package RVMPKG2

Бренд: Audiovox Страницы: 15

Бренд: Brink Страницы: 12

Бренд: Mercedes-Benz Страницы: 357

Бренд: AL-KO Страницы: 88

Бренд: Blue Ox Страницы: 8

Бренд: Van Guard Страницы: 12

Бренд: Kia Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды