Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 42

Страница: 42 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

Examine the brush holders:

The brush holder insulators must be clean and in good condition and all of the hardware must be in

place. See

Figure F.11

. Replace any insulators that are cracked or damaged in any way.

When installing the brush holders, they should be rotated toward the brush retainer (clockwise

rotation when facing the brush holder mounting screw.) until they stop. The edge of the brush

holder plate should be parallel with the surface of the commutator and positioned .030 to .090 from

the surface of the commutator. The brush holder mounting screw should be tightened to a torque

of 24 to 28 Ft Lbs.

The brush holder plate and retainer assembly must be clean and smooth; nothing should prevent

free movement of the brushes. All electrical connections to the brush holders must be clean and

tight.

The recommended torque for 5/16-18 brush holder connection screws is 8 Ft.-Lbs.

When testing is complete, attach the sheet metal cover protecting the welder generator brushes,

connect the negative battery terminal and close the left and right side covers.

Figure F.11 – Generator components

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 42 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: