Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 36

Страница: 36 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

seated. Perform the

Brush and Slip Ring Service Procedure (Exciter / Auxiliary Power Alternator)

, if

necessary.

Insulate the lead wires that had been disconnected from the brushes during the static rotor

resistance test. Position and secure them so they cannot become damaged by the spinning rotor.

It is recommended that the ohmmeter leads be securely attached to the brush terminals, using clips

or terminals BEFORE starting the engine. See

Figure F.9

Start the engine and run it at high idle speed (1800 RPM). The resistance should read approximately

40 ohms* at 77 deg. F. (25 deg. C).

Shut off engine and move one of the ohmmeter leads to a good clean chassis ground connection.

10.

Restart the engine and run it at high idle speed (1800 RPM). The resistance should be very high, at

least 500,000 (500k) ohms.

11.

If the resistance readings differ significantly from the values indicated, re-check the brushes and the

brush spring tension. If the brushes and slip rings are good, replace the rotor.

12.

When testing is complete, securely connect the leads to the brush terminals, replace the alternator

cover and close the left and right side covers. See Wiring Diagram.

NOTE:

The resistance of the copper windings will change with temperature. Higher temperatures

will produce higher resistance and lower temperatures will produce lower resistance.

Figure F.9 – Slip ring locations

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 36 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: