Lincoln Electric RED-D-ARC DX450 Скачать руководство пользователя страница 36

Страница: 36 / 50

E-5

TROUBLESHOOTING

E-5

DX450 (RED-D-ARC)

Observe all Safety Guidelines detailed throughout this manual

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Authorized Field Service Facility

for technical troubleshooting assistance before you proceed.

CAUTION

PROBLEMS

(SYMPTOMS)

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

No welding power output.

Welder has output but no control.

Wire feeder does not work when

control cable is connected to 14 pin

connector.

No auxiliary power.

1. P o o r w o r k l e a d c o n n e c t i o n t o

work. Make sure work clamp is

tightly connected to clean base

metal.

2. "Weld Terminals" switch in wrong

position. Place switch in "Weld

T e r m i n a l s O n " p o s i t i o n w h e n

welding without control cable.

3. Faulty PC board or welder alterna-

tor.

1. Poor remote/control cable connec-

tion to 3-pin or 14-pin connector.

Check connections.

2. Faulty remote cable or faulty wire

f e e d e r o r w i r e f e e d e r c a b l e .

Replace if necessary.

3. Faulty control potentiometer or PC

board.

1. Wire Feeder Power circuit breaker

o p e n . C h e c k 4 2 V b e a k e r a n d

reset if tripped.

2. Faulty control cable. Repair or

replace cable.

3. Faulty wire feeder. Replace wire

feeder.

1. Open circuit breakers. Reset

breakers. If breakers keep tripping

reduce power draw.

2. GFCI module may have tripped.

Follow “GFCI Module Testing and

Resetting Procedure” in the MAIN-

TENANCE section of this manual.

3. Faulty connections to auxiliary

receptacles. Check connections.

4. Faulty PC board or welder alterna-

tor.

If all recommended possible areas

o f m i s a d j u s t m e n t h a v e b e e n

checked and the problem persists,

Contact your local Authorized

Field Service Facility.

Содержание RED-D-ARC DX450



















































Результаты поиска

Содержание RED-D-ARC DX450

Отзывы:

Похожие инструкции для RED-D-ARC DX450

Бренды по названию

Популярные бренды

Lincoln Electric RED-D-ARC DX450, Руководство оператора

Результаты поиска

Содержание RED-D-ARC DX450

Отзывы:

Похожие инструкции для RED-D-ARC DX450

Бренды по названию

Популярные бренды