manualshive.com logo in svg

Lincoln Electric RANGER GXT, Руководство оператора

Поделиться
Скачать
Lincoln Electric RANGER GXT Скачать руководство пользователя страница 23

C-2

ACCESSORIES

C-2

RANGER GXT

RECOMMENDED EQUIPMENT

STICK

K704 Accessory Kit which includes:

•

  Electrode Holder & Cable

•

  Work Clamp & Cable

•

  Headshield

WIRE FEED

K449 LN-25

- Includes internal contactor for across

the arc operation (no control cable). Provides 

“

cold

”

electrode until gun trigger is pressed. Includes gas
solenoid.

Magnum Gun and Magnum Gun Connector Kit are
required for gas-shielded welding. Innershield Gun is
required for gasless welding.

K126-2

Magnum 350 Innershield Gun

K1802-1

Magnum 300 MIG Gun (for LN-25)

K470-2

Magnum 300 MIG Gun (for LN-15)

K466-10

Connector Kit (for LN-15, K470-2)

K1500-1

Gun Receiver Bushing (for LN-15 & K126-2)

K1870-1

LN-15 Across the Arc Model

TIG

Magnum

™

TIG Torch

K1783-9-

TIG Torch

Magnum Parts Kit and Argon Gas

K930-2 TIG Module

- Provides high frequency and shield-

ing gas control.for AC and DC GTAW (TIG) welding applica-
tions. Its compact case is designed foe easy carrying, com-
plete with a handle. High frequency  bypass is built in
Requires

K938-1

Contactor Kit, 

K936-3

Control Cable, and

K814

Arc Start Switch.

K938-1

Contactor Kit - For use with TIG Module, Provides a

“

cold

”

 electrode until the triggering device (Arc Start Switch)

is pressed.

K936-3

Control Cable - Connects TIG Module to RANGER

GXT.

Optional TIG Equipment:

K939-1

Docking Kit - For Mounting the K930-2 TIG Module

on top of the RANGER GXT.

K937-45

Control Cable Extension - Allows TIG Module to be

operated at distances up to 200ft. from the power source.
Available in 45ft. (13.7m).

K844-1

Water Valve Kit - For use with water cooled TIG

torch, Installs inside of TIG Module.

K963-2

Hand Amptrol

K870

Foot Amptrol

REMOTE OUTPUT CONTROL

(See Operations Section for reference)

The Ranger GXT is equipped with a 6-pin connector. The 6-
pin connector is for connecting the

K857

or

K857-1

Remote

Control (optional) or for TIG welding, the 

K870 Foot

Amptrol

or the 

K963-2 Hand Amptrol

. When remote con-

trol is used set the LOCAL / REMOTE switch in the
"REMOTE" position. 

Plasma
K1580-1

Pro-Cut 55 

(Requires Full KVA Adapter 

K1816-1)

Содержание RANGER GXT





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды