manualshive.com logo in svg

Lincoln Electric PANTHER K2874-1, Руководство оператора

Поделиться
Скачать
Lincoln Electric PANTHER K2874-1 Скачать руководство пользователя страница 9

Unpacking the Push-Pull Gun

Safety Precautions

– Read "Safety Precautions" in the Operating Manual before

proceeding. Only personnel that have read and understood
the Operating Manual should install and operate this equipment.

– Power source must be turned "OFF" and power leads disconnected

when installing this unit.

Unpacking the Push-Pull Gun

Carefully unpack your Panther™ Push-Pull Gun and attach the
Barrel Assembly, and make sure you have all of the parts shown
below.

Panther™ Push Pull Gun - INSTALLATION

BARREL

ASSEMBLY

OPERATOR’S

MANUAL

2

Panther™ - PUSH-PULL GUN

KP2744-035A

Contact Tip .035 (0.9mm)

Included

KP2744-364A

Contact Tip . 3/64” (1.2mm)

Installed on Barrel Assembly

KP2746-1

Gas Diffuser

Installed on Barrel Assembly

KP742-1-62R

Gas Nozzle

Installed on Barrel Assembly

KP2773-2

Insulator

Installed on Barrel Assembly

KP2876-1

Drive Roll Kit .035 / 3/64" (.047")

Installed

S26374-64

Tool Kit

Included

Содержание PANTHER K2874-1
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды