manualshive.com logo in svg

Lincoln Electric IDEALARC DC-600 VRD, Руководство оператора

Поделиться
Скачать
Lincoln Electric IDEALARC DC-600 VRD Скачать руководство пользователя страница 10

A-2

INSTALLATION   

IDEALARC® DC-600 VRD

A-2

SAFETY PRECAUTIONS

Read  entire  Installation  Section  before
installing the IDEALARC® DC-600 VRD.

ELECTRIC SHOCK CAN KILL.

• Only  qualified  personnel  should

install this machine.

• Turn  the  input  power  OFF  at  the

disconnect  switch  or  fuse  box
before working on the equipment.

• Do not touch electrically hot parts.

• Always  connect  the  IDEALARC®  DC-600  VRD

grounding  terminal  to  a  good  electrical  earth
ground.

• Set the IDEALARC® DC-600 VRD Power ON/OFF

PUSH  bUTTON  to  the  OFF  position  when  con-
necting power cord to input power.

__________________

SELECT PROPER LOCATION

Place  the  welder  where  clean  cooling  air  can  freely
circulate  in  through  the  front  louvers  and  out  through
the rear louvers. Dirt, dust or any foreign material that
can be drawn into the welder should be kept at a mini-
mum. Failure to observe these precautions can result
in  excessive  operating  temperatures  and  nuisance
shut-downs.

LIMIT ON STACKING

STACKING

Three  IDEALARC®  DC-600  VRD  machines  can  be
stacked.  

DO  NOT

stack  more  than  three  machines  in  one

grouping.

DO  NOT

stack  the  IDEALARC®  DC-600  VRD  on

another type of machine.

Follow these guidelines when stacking:

1. Select  a  firm,  level  surface  capable  of  supporting

the  total  weight  of  up  to  three  machines  (1570
pounds/712 kilograms).

2. Set the bottom machine in place.

3. Stack  the  second  machine  on  top  of  it  by  aligning

the  two  holes  in  the  base  rails  of  the  second
machine  with  the  two  pins  on  top  front  of  the  bot-
tom machine. 

4. Repeat process for third machine.

NOTE

:  The machines must be stacked with the Case

Front  of  each  machine  flush  with  each  other.    See
Figure A.1.

FIGURE A.1  -  Stacking  IDEALARC®  DC-600
VRD machines

TILTING

The  IDEALARC®  DC-600  VRD  must  be  placed  on  a
stable, level surface so it will not topple over.

STACKING HOLE

STACKING PINS

STACKING HOLE

STACKING PINS

WARNING

• Lift  only  with  equipment  of  ade-

quate lifting capacity.

• be  sure  machine  is  stable  when

lifting.

• Do  not  lift  this  machine  using  lift

bail  if  it  is  equipped  with  a  heavy
accessory  such  as  trailer  or  gas
cylinder.

FALLING 

• Do not lift machine if lift bail is 

EQUIPMENT can        damaged.

cause injury.          • Do not operate machine while

suspended from lift bail.

• Do not stack more than three high.
• Do  not  stack  the  IDEALARC®  DC-600  VRD  on  top  of

any other machine.

------------------------------------------------------------------------

WARNING

Содержание IDEALARC DC-600 VRD
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды