Lincoln Electric ARC TRACKER 11724 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

Lincoln Electric ARC TRACKER 11724 Скачать руководство пользователя страница 18

B-5

OPERATION

B-5

ARC TRACKER™

POWER-UP SEQUENCE

When power is applied to the ARC TRACKER™, the
status light will flash green for up to 60 seconds.
During this time the unit is performing a self test. The
status light will also flash green as a result of a system
reset or configuration change during operation. When
the status light becomes steady green the system is
ready for use.

If the status light does not become steady green con-
sult the troubleshooting section of this manual for fur-
ther instruction.

DUTY CYCLE

The ARC TRACKER™ is rated for 1000 A, 44 V DC,
100% duty cycle.

• Note: The correct number and size of welding con-

ductors must be used for proper cooling. See
the installation section for proper connectivity.

COMMON WELDING PROCEDURES

The ARC TRACKER™ can be used with any DC
welding process.

CASE BACK
(TERMINAL COVERS NOT SHOWN)

Case Back Descriptions (See Figure B.2)

1. Left weld terminals (weld current IN)
2. Right weld terminals (weld current OUT)
3. Input cord receptacle

1

2

3

FIGURE B.2

«
...
16
17
18
19
20
...
»

Содержание ARC TRACKER 11724

















































Отзывы:

Нет отзывов