WARNING
6.1 Control Panel and Function Keys
Timer Button
Speed Button
Light Button
Power Button
Motor ON/OFF setting:
Speed setting:
Light intensity setting:
Best results are obtained by using a low speed for
normal conditions and a high speed when odors are
more concentrated.
Turn the hood on for a few minutes before you start
cooking.
The hood should be left on for 15 minutes after
cooking or until all odors have dispersed.
The control switches are located on the front panel of
the unit. See Image below.
This control system consist ot two parts, power panel
and touch panel. Touch panel contains five function
buttons. [power, speed, light, timer and slide control]
Touch timer button when light or motor is working
and the hood will enter into timer setting. When pilot
timer is flashing, slide [ ] to select the timer
section. Choose from 5-10-15-20-25-30-35-40.
The motor and light will be off automatically when
timer is finished. The hood will work with the same
timer setting when you turn it on again.
Touching the speed or control the light intensity
when timer is set will turn off the timer function
automatically.
Press the button to switch the rangehood on and off.
The rangehood will work at the speed that works the
last time.
Touch the POWER button for 2seconds, the
rangehood will slide upwards and works at first
speed. Touch again for another 2seconds, the
rangehood slides down and stops working.
Touch the speed button, the motor turns on; touching
it again will turn it off.
When the hood slides up, the light will turn on
utomatically for 8-10 seconds.
Touch the light button to turn on and off.
Touch this area , slide your finger on it.
Sliding through 1st and 2nd bar (lowest speed),
3rd-4th (2nd speed), 5th-6th (3rd speed), 7th-8th (full
speed).
The rangehood may only be operated when the aluminum
stainless steel grease filter and of the rangehood is installed
(see “Installation Instructions” section).
Clean the cooking zone before using the cooktop for the
first time (see the “Cleaning” section).
Observe all safety and warning information during
operation (see the “General Safety Instructions” section).
Touch the light button to flash the pilot light
- slide [ ]button to control the light’s intensity.
Pilot light stops flashing if no function adjusment
is made in 15 seconds.
6. OPERATION
8
5.3 Installation [Air Extraction]
The following rules must be strictly observed to
achieve optimum air extraction.
Make sure that the exhaust pipe extends as short and
straight as possible.
Do not reduce the size or restrict the exhaust pipe. When
using exhaust air pipes, always install the pipe tightly to
minimise pressure loss.
Non-compliance with these basic instructions will reduce
the performance and increase the noise level of the
rangehood.
All installation work must be carried out by an
electrician or a qualified person.
Do not connect the exhaust pipe of the rangehood to an
existing ventilation system used for another appliance,
e.g. a flue, gas pipes or hot air pipes.
In case the exhaust air pipe is bent, the angle of the
exhaust air pipe should not be less than 120°. Never
point the exhaust air pipe downwards, but always
horizontally or guide the pipe from the starting point
upwards to the air outlet on the outside wall.
After installation, please make sure that the rangehood is
positioned horizontally to prevent grease from
accumulating.
Make sure that the exhaust pipe selected for installation
complies with the relevant standards and is fire-retardant.
CAUTION
Before installation, it is important to read the information given
on the following pages as well as the "Appliance Dimensions"
and the "Warning and Safety instructions" sections at the
beginning of this booklet. This is particularly crucial when using
the rangehood at the same time as a heating appliance that
relies on oxygen from the same room, which could result in the
build-up of toxic fumes.
The rangehood should be installed according to local and
national building regulations. Seek approval from the building
inspector where necessary.
CAUTION
Risk of injury! For safety reasons, only use the size of fastening or
mounting screw recommended in these operating instructions.
Non-compliance with these instructions can lead to injuries and
electric shocks.
Remember that any constriction of the airflow will reduce extraction
performance and increase operating noise.
NOTE
cont. installation
