- -
14
EEPROM 2.0 4.0 4.0 5.0 7.0 5.0 4.0 7.0 7.0 4.0 6.0 6.0 4.0 5.0 4.0 2.0 5.0 4.0 3.0 4.0
P13
Incline profile 13
Segment
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19 20
EEPROM
5
5
5
6
6
6
4
4
6
6
5
5
8
8
9
9
9
7
4
2
Speed profile 13
Segment
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19 20
EEPROM 2.0 4.0 4.0 7.0 7.0 4.0 7.0 8.0 4.0 8.0 9.0 9.0 4.0 4.0 4.0 5.0 6.0 3.0 3.0 2.0
P14
Incline profile 14
Segment
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19 20
EEPROM
5
6
6
6
7
5
8
8
4
4
4
5
5
8
8
10 10
8
6
3
Speed profile 14
Segment
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19 20
EEPROM 2.0 4.0 5.0 6.0 7.0 5.0 4.0 6.0 8.0 8.0 6.0 6.0 5.0 4.0 4.0 2.0 4.0 4.0 3.0 3.0
P15
Incline profile 15
Segment
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19 20
EEPROM
3
4
5
4
6
5
6
4
3
3
3
5
5
6
7
6
8
5
4
3
Speed profile 15
Segment
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19 20
EEPROM 2.0 3.0 3.0 6.0 7.0 5.0 4.0 5.0 7.0 8.0 6.0 7.0 5.0 5.0 6.0 3.0 4.0 4.0 3.0 2.0
PS: Pls. Attention that the in above profile, the red documents of EEPROM are all display data, instead of
number Moreover, the Speed is displayed in Mile data.
4-1.
Safety key: normal close / active open:
4-1-1.
When we open the safety key, the hardware power off, the motor & incline motor will be stop at
once.
4-1-2.
When it starts, it will return to the incline motor, the display default will choose the states of the
program.
4-2.
Start / stop key:
4-2.1.
When we press the “start key”, it will make a signal output as per the choosing program. The signal
is more adjustive.
4-2.2. When we press the “stop key”, the treadmill will stop immediately, the DC motor will decline slowly
to stop state and all of the data will clear.
4-3.
Program Key: Press the key under the stop state, choosing the program which we want, 2
seconds later, the LED will display the relative profile graph. The operation processes are as
follows:
M→ P1→P2→ P3→ P4→P5→P6→P7→…P15→U1→U2→U5→M.
When we choose P1~P12 or USER program, the dot matrix will firstly show the number of this
program, then show the profile of this program. For example, when we choose P15, the dot
matrix will firstly show 15, 2s later, the profile of the program will come out. If we continuously
press the Program Key to cycle the program, the dot matrix will only show the program number.
The profile will be never showed unless we release the press in 2s.
4-4.
Clear key:
4-4.1.
All the parameter will be clear when we press this key, whenever it is in the stand by state, setting
processes or we press the STOP key. The incline will get back to its original data and the system
will return to its stand by state. However, it will not be available when it is in the running state.
Содержание D15.0
Страница 1: ... 0 OWNER S MANUAL ...
Страница 27: ...4 EXPLODED DRAWING ...
