5. Power off:
5.1 Device will automatically shut off if left idle for more
than 1 minute to extend battery life.
5.2 Manually power off the device by pressing the
ON/MEM
button.
Please make sure the probe is clean to ensure an
accurate reading.
1. The probe lens is the most delicate part of the
thermometer. Use with care when cleaning the probe
lens to avoid damage.
a. Use the 70% alcohol swab or the soft cotton moistened
with the 70% alcohol to clean the probe lens.
b. Allow the probe to fully dry for at least 1 minute.
c. Keep the unit dry and away from any liquids and
direct
sunlight.
d. Storage temperature range: It should be stored at
room temperature between -4~122°F (-20~50°C), RH
≤
85%
e. The Probe should not be submerged into liquids.
2. Holding the thermometer too long may cause a higher
ambient temperature reading of the probe.
This could make the body temperature measurement
lower than usual.
Use
Cleaning and Storage
This device is supplied with one lithium cell CR2032x1.
1. Open the battery cover: Insert a pointed object into
battery cover pick hole. At the same time, use thumb to
push battery cover out. (See Figure 1)
2. Hold the device and flip the battery out with a small
screwdriver. (See Figure 2)
3. Insert a new battery under the metal hook and press
down until you hear a “click” sound. (See Figure 3)
4. Replace the battery cover
The positive (+) side up and the negative (-) side
pointed
down.
Figure 1
Figure 2
Figure 3
Battery Replacement
Error Message Problem
Error 5~9, the system
is not functioning
properly.
Measurement before
device stabilization.
Wait until all the icons
stop flashing.
The ambient
temperature is not
within the range
between 50°F~104°F
(10°C~40°C).
Allow the thermometer
to rest in a room for at
least 15 minutes at room
temperature: 50°F~104°F
(10°C~40°C).
(1) In forehead mode:
Temperature taken is
higher than 108°F
(42.2°C)
(2) In surface mode:
Temperature taken is
higher than 176°F (80°C)
Please select the target
within specifications. If a
malfunction still exists,
please contact the
nearest retailer.
(1) In forehead mode:
Temperature taken is
lower than 93.2°F (34°C)
(2) In surface mode:
Temperature taken is
lower than -7.6°F
(–22°C)
Please select the target
within specifications. If a
malfunction still exists,
please contact the
nearest retailer.
Device cannot be
powered on to the
ready stage.
Change the battery.
Unload the battery, wait
for 1 minute and repower
it. If the message
reappears, contact the
retailer for service.
Solution
Troubleshooting:
3. Measuring body temperature on the forehead:
Press the ON/MEM button to power on the device.
Forehead mode is the default mode. You can see the
icon on the screen and hear two beep sounds. In this
mode, you can hold the thermometer within 3 cm from
the central forehead and press the "Scan" button to get
the forehead measurement. The time consuming for
measurement might be 1 second.
NOTES:
a. Forehead temperature is displayed in oral mode. This
mode converts the forehead temperature to display its
“oral-equivalent”
value.
b. Before the measurement, please stay in a stable
environment for 5 minutes and avoid exercise, bath for
30mins.
c. Remember to keep the forehead area clean and away
from sweat, cosmetics and scar while taking temperature.
d. The “Clinical Bias” is 29.5~28.9°F (-1.4 ~ -1.7°C).
e. The “Limits of Agreement” is 0.98.
f. The "Repeatability" is 32.4°F (0.20°C).
4. Measuring surface temperature:
4.1 After power on, press and hold the ON/MEM button,
and press the “SCAN” button one time for “Infrared
thermometer” mode to see icon on your LCD display.
In this mode, you can get the target surface temperature.
4.2 When you press the “Scan” button, you will get the real
time temperature immediately. If you press and hold the
“Scan” button, the reading of measurement will be
continuously
updated.
4.3 Applications include temperature measurements for
water, milk, cloth, skin or other objects.
Note: This mode shows the actual and unadjusted surface
temperature which is different from the body temperature.
Use
Distributed by
C&A Marketing, Inc., 2 Bergen Turnpike
Ridgefield Park, NJ 07660
MADE IN CHINA
LIL’ JUMBL is a trademark of C&A IP Holdings, LLC
©2015 All Rights Reserved
