Lika MTA1 Скачать руководство пользователя | Manualshive

Страница: 31 / 48

background image

SMA1

7 - BiSS C-mode interface

Order code: standard SMA1-SCx-5-…

SMA1 is a Slave device and complies with the “BiSS C-mode interface” and the
“Standard encoder profile”.
For detailed information not listed in this manual please refer to the official
BiSS website (www.biss-interface.com).
The device is designed to operate in a point-to-point configuration and has to
be installed in a “single Master - single Slave” network.

WARNING

Never connect the sensor in a “single Master - Multi Slave” network.

CLOCK MA and DATA SLO signal levels comply with the “RS-422 EIA standard”.

7.1 XML file

The product is supplied with an XML file

idbiss4C69.xml

(see at

www.lika.biz

).

Install the XML file in your BiSS Master device.

7.2 Communication

The BiSS C-mode protocol uses two types of data transmission protocols:



Single Cycle Data (SCD):

this is the primary data transmission protocol. It

is used to transmit the process data from the Slave device to the Master
device. See the “7.3 Single Cycle Data” section on page 32.



Control Data (CD):

transmission of a single bit following the SCD data. It is

used to read data from or write data to the registers of the Slave. See “7.4
Control Data CD” section on page 33.

MAN SMA1 E 2.9.odt

7 - BiSS C-mode interface

31 of 48

«
...
29
30
31
32
33
...
»

Содержание MTA1

















































Отзывы:

Нет отзывов

Похожие инструкции для MTA1

Бренд: Teac Страницы: 18

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 30

Бренд: Yamaha Страницы: 30

Бренд: Yamaha Страницы: 56

EF4500iSE - Inverter Generator

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

RX-Z11 - AV Receiver

Бренд: Yamaha Страницы: 4

Бренд: Yarvik Страницы: 36

Бренд: YASKAWA Страницы: 4

Бренд: Reach Страницы: 13

Бренд: Humandata Страницы: 10

Бренд: Lindy Страницы: 2

Бренд: AJA Страницы: 43

HDMI to YUV/YPbPr

Бренд: J.S. Technology Страницы: 2

Бренд: Cross Technologies Страницы: 24

Бренд: Delta Electronics Страницы: 181

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды