Lika MTA1 Скачать руководство пользователя

Страница: 25 / 48

SMA1

Configuration

[49, rw]

Bit

Function

Bit = 0

Bit = 1

Select BiSS / SSI

BiSS

SSI

Set preset / offset

Preset

Offset

Enable preset / offset Enable

Disable

Not used

Output code

Gray

Binary

Counting direction

Standard

Inverted

Not used

: it affects the absolute position information, not the sine/cosine signals

Select BiSS / SSI

It sets whether the output data is transmitted using the BiSS B-mode protocol
(0) or the SSI protocol (1).
Default = 0 (BiSS B-mode)

Set preset / offset

This parameter is available only if the parameter

Enable preset / offset

is set to

ENABLE. It allows to activate either the preset function (

Set preset / offset

PRESET) or the offset function (

Set preset / offset

= OFFSET); the Preset or

Offset value has to be set in the

Preset / Offset

the preset / offset functions (

Enable preset / offset

= ENABLE), this item allows

to activate either the preset function or the offset function. The value set in the

Preset / Offset

of this parameter whether it is set to PRESET (0) or OFFSET (1). In the first case
(

Set preset / offset

= PRESET) the

Preset / Offset

preset value; while in the second case (

Set preset / offset

= OFFSET) the

Preset

/ Offset

value use the

Save and activate Preset / Offset

function in the

Command

Preset /

Offset

Default = 0 (Preset)

Enable preset / offset

It enables / disables the preset / offset functions. After having enabled the use of
the functions you have to choose whether to activate the preset or the offset in
the

Set preset / offset

parameter. Then to active a new value, set it next to the

Preset / Offset

Save and activate Preset / Offset

command (set “02” in the register 48).
Default = 0 (enable)

MAN SMA1 E 2.9.odt

6 - BiSS B-mode interface

25 of 48

Содержание MTA1

















































Результаты поиска

Содержание MTA1

Отзывы:

Похожие инструкции для MTA1

Бренды по названию

Популярные бренды

Lika MTA1, Руководство пользователя

Результаты поиска

Содержание MTA1

Отзывы:

Похожие инструкции для MTA1

Бренды по названию

Популярные бренды