Lightware HDMI-3D-OPT-RX150RA Скачать руководство пользователя страница 80

Страница: 80 / 97

8. Firmware Upgrade

HDMI-3D-OPT series – User's Manual

Firmware Components

The components of the installed and update firmware version for the selected devices are listed on the

following screen. (Update version will be uploaded to the device.)

Add a device by clicking on the

Add device

button. The previous screen will be shown; select the desired

device(s) and click

Remove a device by selecting it (highlight with yellow) and clicking on the

Remove device

button, or by clicking

Remove all

button to clear the list.

Enabling

Factory reset

will perform factory default values for all settings in the device. Three different status

can exist:

▪

Enabled by user

: all settings will set to factory default values.

▪

Disabled by user

: your settings will be saved and restored after upgrading.

▪

Enabled by default and not changeable by user

: firmware upgrade must perform a factory reset to apply all

changes coming with the new firmware version.

Click on the

Next

button to continue.

Step 3.

Upgrade the device.

Click on the

Start

button to start the upgrade process.

Two warning windows will pop up before upgrading the device:

▪

Do not power off the device or unplug the USB
cable whilethe upgrade is in progress. Click

continue.

▪

The device presets will be lost after the upgrade.



 



Содержание HDMI-3D-OPT-RX150RA


































































































Результаты поиска

Содержание HDMI-3D-OPT-RX150RA

Отзывы:

Бренды по названию

Популярные бренды

Lightware HDMI-3D-OPT-RX150RA, Руководство пользователя

Результаты поиска

Содержание HDMI-3D-OPT-RX150RA

Отзывы:

Бренды по названию

Популярные бренды