Port Diagram (of TX130 models)
Restore Factory Default Settings
1.
Keep the Show me button pressed for 10 seconds. After 5 seconds front panel LEDs
start to blink but keep the button pressed. The LEDs start to blink faster 5 seconds later.
2.
Release the button, then press it 3 times quickly; factory default settings are restored:
IP Address (static)
192.168.0.100
Subnet Mask
255.255.255.0
Static Gateway
192.168.0.1
DHCP
Disabled
TCP/IP Port No.
LW2: 10001; LW3: 6107
Selected Output port
Video: VGA; Audio: Analog Audio input
Autoselect
Disabled
Output TPS Mode
Auto
Emulated EDID
VGA port: F89; DP, HDMI ports: Dynamic
RS-232 Mode
Pass-through
RS-232 Control Protocol
LW2
RS-232 Port Setting
57600 BAUD, 8, N, 1
RS-232 Command Injection Port No.
Local: 8001; TPS: 8002
IR Command Injection Port No. (local)
Input: 9001; Output: 9002
IR Command Injection Port No. (TPS)
Input: 9003; Output: 9004
Typical Application
Software Control – Using Lightware Device Controller (LDC)
The device can be controlled from a computer through the Ethernet port
using Lightware Device Controller. Please download the application from
www.lightware.com
, install on a Windows PC or a Mac OS X and connect to
the device via the Ethernet port. LDC software contains many useful built-in
tools which can be used for signal analysis like the followings:
Front Panel Button Functions
Video Input Selection
The desired video input can be selected by pressing the Video select button on
the front panel. The selection order of the inputs depend on the model as follows:
TX120 models:
TX130 models:
Audio Input Selection
The desired audio input can be selected by pressing the Audio select button on
the front panel. The selection order of the inputs depend on the model.
If 4K video is selected to the output, analog audio cannot be embedded to the
video stream due to the limitations of the video IC, thus the original audio stream
will be transmitted.
Cross Audio-embedding: The video and audio inputs can be combined with limitations.
Below table contains the allowed connections:
The video and audio inputs can be also selected by using LDC (Lightware Device
Controller), sending a protocol command, or using Autoselect.
Lock / Unlock Buttons
Press the Audio select
and the
Show me buttons together.
Set a Dynamic IP Address
1.
Keep the Show me button pressed for 5 seconds; all front
panel LEDs start to blink.
2.
Release the button, then press it 3 times quickly. DHCP is
now enabled.
Autoselect
VGA
HDMI
Autoselect
VGA
DP
HDMI
Audio source
HDMI
DP
Audio
Video
source
HDMI
-
DP
-
VGA
-
-
Maximum Twisted Pair Distances
Below values are valid when the transmitter is powered by a local adaptor; distances may
decrease depending on the powering mode (local or remote) and cable quality.
Resolution
Pixel
clock rate
Cable lengths
(Auto / Long reach TPS mode)
CAT5e
AWG24
CAT7
AWG26
CAT7
AWG23
1024x768@60Hz
65 MHz
100 m / 130 m* 90 m / 120 m* 120 m / 170 m*
1280x720p@60Hz
73.8 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*
1920x1080p@60Hz (24bpp)
148.5 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*
1920x1200@60Hz
152.9 MHz
100 m / NA
90 m / NA
120 m / NA
1600x1200@60Hz
162 MHz
100 m / NA
90 m / NA
120 m / NA
1920x1080@60Hz (36bpp)
222.75 MHz
70 m / NA
70 m / NA
120 m / NA
3840x2160@30Hz UHD **
297 MHz
70 m / NA
70 m / NA
100 m / NA
4096x2160@30Hz 4K **
297 MHz
70 m / NA
70 m / NA
100 m / NA
* Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz.
** If 4K video is selected to the output, analog audio cannot be embedded to the video stream
due to the capabilities of the video IC, thus the original audio stream is transmitted.
CAT7 SFTP AWG23 cable is always recommended.
Mounting Options - WP-UMX-TPS Wall Plates
Thanks to the design of Lightware devices, WP-UMX-TPS wall plates transmitter can be
mounted easily into an industrial standard box as the figures show below. B225R switch/outlet
box is not supplied with the product, it can be purchased separately.
1
Release and remove the fixing screws from the front
side of the extender.
2
Insert the extender into the B225R outlet box and position
it to get the holes aligned.
3
Fasten the front side of the extender to the B225R
outlet box by fitting all the screws.
Mounting Options - FP-UMX-TPS-TX130-MKM
FP-UMX-TPS-TX130-MKM bracket is supplied with the product.
It is compatible with the CRMB265 floorbox type
(MK Cablelink Plus Modular series).
VIDEO
SELECT
AUDIO
SELECT
SHOW
ME
AUDIO
SELECT
+
SHOW
ME
+
SHOW
ME
5 sec
3x
WP-UMX-TPS-TX130-US
VIDEO
SELECT
ETHERNET
INPUT ST
ATUS
VIDEO
AUDIO
O
RESET
IR
VGA
DP
HDMI
Auto
sele
ct
AUDIO
SELECT
SHOW
ME
2
DP
IN
3
AUDI
O
DP
HDMI
TPS L
ink
analog
audio
Laptop
Ethernet
switch
MAC
WP-UMX-TPS-
TX130-US Black
Blu-ray
player
WiFi
access
RS-232
HDMI
IR
DP
HD Projector
LAN
LAN
CATx
HDMI
VGA
HDMI-
TPS-RX97
Sn:
Made in EU, Hungary
RoHS
Ethernet 10/100
Bidirectional IR
Bidirectional RS-232
HDMI,
3D, 4K supported
H HDDMM
I I--TTPP
S S--RRXX
9 977
Sn:
T TPPSS
LLoo
n ngg DD
i issttaa
n nccee RR
e ecceeiivv
e err
PIN: 2mm
12V 1A
DC
For
best performance us
e AW
G23 CA
T6 or CA
T7 SFTP
cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3
af)
TP
S IN
Po
E
(
)
Local
DC cable
CATx
TPS-PI-1P1
48 DC
IN
Typ
ical
: 0.7
A
Max
: 1.5
A
- +
Max:
2.5A
PI
N: 2mm
48V DC
Power
adaptor
Power send
DP in
VGA in
Audio in
Digital video in
Embedder
Processor
De-embedder
De-embedder
A/D converter
A/D converter
HDMI in
RS-232
in/out
Ethernet
IR detector
TPS out
Digital video in
Analog video in
Analog
stereo audio
1
2
3
100.6
109.2
70.6
B225R switch/outlet box
Fitting screw
Front side of the transmitter
2
1
Loose the two
fixing
screws
on the top of the
bracket
. Insert the device
into the frame.
Move the
handles
towards the frame. Align
the
tab
on the assembly
with the slot in the frame.
3
Fasten the
fixing
screws
to fix the device into the
floorbox frame.
Tab
Fixing screw
Handle
FP-UMX-TPS-TX130-MKM
FP-UMX-TPS-TX130-MKM
bracket
53.4
77
217