Lightware 91540021 страница 101 Скачать руководство пользователя

Страница: 101 / 119

8. Firmware Upgrade

HDMI-TPS-RX110AY series – User's Manual

101

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

8.6.

Remote Firmware Upgrade of Connected Lightware Devices

FirmwareofLightwaredevicescanbeupgradedviaanotherconnectedLightwaredevicewithoutremoving

the device from the system. It means user does not have to connect directly to the upgradable device, it can

bereachedandflashedthroughotherdevices.It’samorecomfortablewaytokeepup-to-dateyourLightware

devices.

Therearetwotypesofremoteupgrading:

Extended Upgrade

▪

IntelligentdevicescanbeupgradedviaanotherintelligentorbasicdeviceviaTPSorOPTS/OPTMlink.

▪

For example, HDMI-TPS-RX110AY series extenders can be upgraded via MMX6x2-HT series matrix or
a HDMI-TPS-TX95 extender.

Hosted Upgrade

▪

Basic devices can be upgraded only via an intelligent device via TPS link.

▪

For example, TPS 95 series extenders can be upgraded via MMX6x2-HT series matrix or
HDMI-TPS-RX110AY series extenders.

▪

In case of hosted upgrade, the procedure is almost the same as described in Firmware upgrade –

StarttheLDU2ApplicationandFollowtheSteps

. The only difference is that the host device’s name,

and IP address appears beside the name of the device to be upgraded.

ATTENTION!

During hosted upgrade the host device turned to bootload mode when the extender is

upgraded.Duringtheupgradenormaloperationmodeissuspended.Whentheupgradeissuccessfully

finished,thenormaloperationmodeisrestored.



 



Содержание 91540021
























































































































Результаты поиска

Содержание 91540021

Отзывы:

Похожие инструкции для 91540021

Бренды по названию

Популярные бренды

Lightware 91540021, Руководство пользователя

Результаты поиска

Содержание 91540021

Отзывы:

Похожие инструкции для 91540021

Бренды по названию

Популярные бренды