Lightware 91540021 Скачать руководство пользователя страница 97

Страница: 97 / 119

8. Firmware Upgrade

HDMI-TPS-RX110AY series – User's Manual

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

ATTENTION!

While the firmware is being upgraded, the normal operation mode is suspended as the

receiverisswitchedtobootloadmode.Signalprocessingisnotperformed.Donotinterruptthefirmware

upgrade. If any problem occurs, reboot the receiver and restart the process.

ATTENTION!

Thefirmwareupgradeprocesshasaneffectontheconfigurationandthesettingsofthe

device. For more details, please see the

KeepingtheConfigurationSettings

section before the upgrade.

8.1.

About the Firmware Package (LFP2 File)

ThefirmwarefilesarepackedinanLFP2package.Youneedonlythisfiletodotheupgradeonyourdevice.

▪

Thepackagecontainsallthenecessarycomponents,binary,andotherfiles;

▪

Thepackagealsocontainseachfirmwarewithversionnumberandalistshowingthecompatible

devices.

8.2.

Short Instructions

Step 1.

GetthefirmwarepackandtheLightwareDeviceUpdaterv2(LDU2)application.

Step 2.

InstalltheLDU2application.

Step 3.

Establish connection between the computer and the device(s) via Ethernet.

Step 4.

StartLDU2andfollowtheinstructionsshownonthescreen.

8.3.

Installation of LDU2

Minimum System Requirement

RAM

:1GB

Installation Modes

LDU2hastwoinstallationmodes:

Normal

and

Snapshot

Normal install

Snapshot install

AvailableforWindowsandmacOS

AvailableforWindows

The installer can update only this instance

Cannot be updated

Only one updateable instance can exist for all users More than one different version can be installed for each user

Comparison of install types

ATTENTION!

Using the Normal install as the default value is highly recommended.

Installation for Windows OS

Run the installer. If the User Account Control drops a pop-up message click

Yes

. During the installation you

will be prompted to select the type of the installation.

Installation for macOS

MounttheDMGfilewithdoubleclickingonitanddragtheLDU2iconovertheApplicationsicontocopythe

programintotheApplicationsfolder.IfyouwanttocopytheLDU2intoanotherlocationjustdragtheicon

over the desired folder.

INFO:

AftertheinstallationtheWindowsandthemacOSapplicationhasthesamelookandfunctionality.

8.4.

Detailed Instructions

8.4.1.

Establish Connection

Make sure that the computer and the device are connected over

Ethernet

and the connection is established

between them.

8.4.2.

Start the LDU2 Application and Follow the Steps

The Steps of the Upgrade in Quick Summary:

Step 1.

Selectthefirmwarepackagefile.

Step 2.

Select the unit(s) for upgrading.

Step 3.

Check the upgrade parameters.

Step 4.

Starttheupdateandwaituntilitisfinished.

Step 5.

Waituntiltheunitrebootswiththenewfirmware.



 



Содержание 91540021
























































































































Результаты поиска

Содержание 91540021

Отзывы:

Бренды по названию

Популярные бренды

Lightware 91540021, Руководство пользователя

Результаты поиска

Содержание 91540021

Отзывы:

Бренды по названию

Популярные бренды