READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:4A28442
A0501
Page 2 of 2
A
COMPANY
631 Airport Road, Fall River, MA 02720
Final Installation:
1.
If a SUPPORT PLATE is provided (Fig. 4), drop CROSSBAR
down into SUPPORT PLATE as shown.
2.
Using appropriate slots in CROSSBAR, secure CROSSBAR
and SUPPORT PLATE to OUTLET BOX using OUTLET BOX
SCREWS (provided with outlet box).
3.
If SUPPORT PLATE is being used, secure SUPPORT PLATE
directly to ceiling surface using four MOUNTING HOLES. Use
appropriate fasteners for the type of ceiling (i.e. wood screws,
molly bolts, etc.).
4.
Slide CANOPY over the SWIVEL BALL (Fig. 6).
5.
Raise CHASSIS and SUSPENSION assembly to CROSS
BAR. Position SWIVEL BALL through the opening in the end
of the CROSSBAR as shown in Fig.5.
6.
Allow SWIVEL BALL to rest down inside the CROSS BAR
making certain the TAB on CROSSBAR is aligned with slot in
SWIVEL BALL.
Wiring Luminaire:
Conventional Wiring
(all lamps on, single switch):
1.
Make connections: BLACK and RED luminaire leads to hot
supply lead; white luminaire lead to neutral (white) supply
lead. Green luminaire lead is a ground wire and must be
connected to grounding terminal or ground lead inside
OUTLET BOX. Use WIRE NUTS (local hardware item). Push
supply wires and connections back into OUTLET BOX.
Multi-Level Wiring
(all lamps on or only two lamps
on, two switches):
Note: Requires two separately switched hot supply leads.
Option not available on two lamp units.
1.
Make connections: BLACK luminaire lead to first hot supply
lead; RED luminaire lead to second hot supply lead; white
luminaire lead to neutral (white) supply lead. Green luminaire
lead is a ground wire and must be connected to grounding
terminal or ground lead inside OUTLET BOX. Use WIRE
NUTS (local hardware item). Push supply wires and
connections back into OUTLET BOX.
2.
Snap CROSSBAR CLIP onto CROSSBAR as shown in Fig. 5
and secure CLIP in place by tightening CLIP SCREW.
Canopy Installation:
1.
Slide CANOPY up STEM aligning SLOTS in INNER CANOPY
with SCREWS protruding from CROSSBAR (Fig. 6).
2.
Rotate CANOPY clockwise until CANOPY snaps securely
against ceiling.
3. Install
recommended
lamps
Final Suspension Assembly:
Traditional 3-Arm Suspensions
1.
Pass un-threaded end of ROD up into hole in side of
COLLECTOR (Fig. 8). Secure in position by threading ROD
into SWIVEL BRACKET (Fig. 7). Repeat for remaining
RODS.
Contemporary 3-Cable Suspensions
1.
Thread PLUNGER into SWIVEL BRACKET
2.
Push end of CABLE through PLUNGER opening until CABLE
is tight (Fig. 9). Repeat for remaining CABLES.
CAUTION: Luminaire may weigh up to 40 lbs.
Always use Support Plate (when provided) with
the appropriate mounting hardware
.
CANOPY
SCREW
INNER
CANOPY
FIG. 6
CROSSBAR
DECORATIVE
KNOB
SUPPORT
CAP
OUTER
DIFFUSER
CANOPY
OUTLET BOX
SCREWS
WIRE NUT
OUTLET BOX
CLIP SCREW
CROSSBAR
CLIP
SWIVEL
BALL
FIG. 5
FIG. 4
FIG. 7
SWIVEL
BRACKET
FIG. 8
COLLECTOR
ROD
FIG. 9
SWIVEL
BRACKET
CABLE
PLUNGER
SUPPORT
PLATE
AUXILIARY
FASTENING
HARDWARE
CROSS BAR
SCREW
