LIGHT MY BRICKS LEGO Winter Village Post Office 10222 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 70

background image

Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.

Connecting cable connectors to Strip Lights

Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.

Connecting Micro Cable connectors to Micro
Expansion Board Ports

Take extra care when inserting the micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is

«
...
2
3
4
5
6
...
»

Содержание LEGO Winter Village Post Office 10222







































































Отзывы:

Нет отзывов

Похожие инструкции для LEGO Winter Village Post Office 10222

Бренд: FENDT Страницы: 31

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Tanco Страницы: 112

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: Underhill Страницы: 12

Бренд: UMS Страницы: 92

Бренд: Mobiak Страницы: 15

MT765 Challenger

Бренд: Fast Страницы: 31

Бренд: Zafferano Страницы: 12

Бренд: Focal Meditech Страницы: 10

Бренд: Rohm Страницы: 17

Бренд: Rainbow Colour Changers Страницы: 22

Бренд: Protech Machinery Страницы: 21

Бренд: Simplicity Страницы: 20

Бренд: TOORX Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды