Light Conversion ORPHEUS Скачать руководство пользователя страница 38

Страница: 38 / 39

ORPHEUS User’s Manual

[email protected]

Light Conversion

TROUBLESHOOTING GUIDE

This section lists the possible problems that might occur while operating ORPHEUS. With each

symptom possible causes and their solutions are presented.

9.1

White Light Generation Does Not Occur/Is Instable

Cause

Corrective action

Pump pulse intensity is too low/high

Refer to paragraph 7.5.

WLG substrate is damaged

Refer to paragraph 7.4.

9.2

Low Parametric Output or No Output at All

Cause

Corrective action

White light generation is instable/no generation

Refer to paragraph 9.1.

Second harmonic generation is inefficient

Refer to paragraph 9.3.

Motors are not at their intended positions

Reset all OPA motors thr

ough the “

Motors

”

section.

Beam misalignment inside ORPHEUS

Refer to paragraph 7.3 and contact Light Conversion
support team for an additional help.

9.3

Low Second Harmonic Generation Efficiency

Cause

Corrective action

SHG Crystal is not at phase matching angle

Optimize the

angle through “

Motors

”

section in the

WinTOPAS software.

Pump pulse compression is not optimal

Optimize the pulse compression of the pump laser while
monitoring the output power of second harmonic or
Signal.

Low pump pulse contrast

Adjust the timing of Pockels Cells while monitoring the
second harmonic of pump or Signal power.

Содержание ORPHEUS








































Результаты поиска

Содержание ORPHEUS

Отзывы:

Похожие инструкции для ORPHEUS

Бренды по названию

Популярные бренды

Light Conversion ORPHEUS, Руководство пользователя

Результаты поиска

Содержание ORPHEUS

Отзывы:

Похожие инструкции для ORPHEUS

Бренды по названию

Популярные бренды